Mounting plate for CB antennas on Land Rover Defender, for left-hand drive (LHD) This mounting plate optimally attaches a CB antenna to the air intake of the Land Rover Defender. For this purpose, the mounting plate is installed on the left (as seen from the driver's seat) ventilation grille / on the air inlet. For right-hand drive vehicles (UK), please contact us by phone or e-mail. Please select the suitable variant for you: fixed mounting or as a magnet. Delivery: mounting plate 1 m ground cable mounting material

Brief description: DV antenna cable 5m RG58 with PL foot incl. Weather protection cap and FME PL adapter - solderless This article is perfect as a roof duct for an antenna cable to operate a CB radio system. The supplied cover cap protects the PL foot from the weather when an antenna is not in use. The detachable PL adapter makes it easy to lay the cable inside the vehicle or to carry it out in tight spaces. There is no longer any need for soldering work because this article is provided with a PL screw connection on both sides. This article is ideal if, for example, you want to use our Cargobear antenna holder on our Cargobear in the rear area and are looking for a clean solution for the cable duct in the interior right up to your CB radio.

The ALBRECHT AE 6110 has all the essential functions that you need. The highlight: With a width of only 10 cm and a height of 2.5 cm, it can easily be accommodated even in the smallest of spaces. With its die-cast housing, it is very stable. New: with integrated VOX function for hands-free speaking in the vehicle Properties: All European CB standards S-meter, 6-level LED indicators for RX and TX VOX hands-free function Receiving sensitivity adjustable (RF gain) Channel 9/19 direct selection button (EMG) Die cast housing 4 watt AM / FM Automatic squelch (ASQ), adjustable in 9 levels Further equipment features: Channel selection buttons on the microphone Channel search (scan) Keylock Socket for external speaker Technical specifications:Dimensions: 102 x 100 x 25 mm³Weight: 450 gSupply voltage: 13.2 V.Power consumption: 2 A max.Operating temperature range: -20 to +50 ° CAntenna input: UHF, SO-239Frequency error: <+/- 300 HzTransmission power: 4 wattsInterference transmissions: <4 nW (-54 dBm)Adjacent channel power: <20 µWFM frequency deviation: <1.9 kHzAM modulation depth: <90%Reception sensitivity: better than 1 μV (20 dB SINAD)Mirror selection: 70 dBAdjacent channel suppression: 60 dBAudio output: 1 watt into 8 ohmsFrequency response: 300-3000 Hz Conversion option for licensed amateur radio operators:10 m amateur radio band, 400 channel mode: 25,610-30,105 MHz, 8 watts Scope of delivery: AE 6110 CB radio, microphone with up / down buttons, microphone holder, mounting bracket with screws, instructions

This CB mobile antenna scores with good SWR values - the fine-tuning of the SWR values is done by rings. Technical data: CB mobile antenna 1/4 lambda 120 channels Power rating: 40 watts Material: Stainless steel SWR Adjustable YES Length: 115 cm Cable length: 4 metres For fixed mounting The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio, you still need a PL259/6 plug for RG58 coaxial cable.

Magnetic base antenna for CB radio, approx. 145 cm long. Technical data: Type: 5/8 LambdaPower rating: 200 WLength of steel: 148 cmRadiator material: stainless steelMagnetic base: 120 mm diameterThe antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

The 1/4 lambda antenna is easy to mount and offers a wide bandwidth incl. DV connection. It consists of a stainless steel radiator with flux points and a wing nut. The standing wave ratio is preset and can be changed by changing the radiator length. Mounting instructions: Drill a hole with a diameter of 12 mm at a point on the vehicle body.Deburr the hole and ensure a good conductive connection of the antenna flux.Then insert the antenna base from the outside of the body into the hole so that the corrugated side of the antenna joint faces the outside of the vehicle. Fit the plastic washer and the metal trident washer the right way round. Fit the toothed washer and screw on the nut loosely After aligning the base, tighten the nut on the inside of the body with a spanner Screw on the angle plug with the antenna cable (tip: seal with silicone to permanently seal the mounting point against rust) Mount the radiator with the threaded bolt on the antenna base Technical data: Frequency: MHz 26-28 Type: 1/4 Lambda Power rating: 300 W Radiator length: 130 cm Steel material: Stainless steel SWR Adjustable - SWR adjustment via length change: SWR preset Special features: Plug type DV Total length with base: 138 cm The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

Alan PL259/6 plug, for RG58 coaxial cable PL259/6 plug, double pack, for assembling RG58 antenna cables.Required for the Alan ML130 and Alan ML145 magnetic antenna.

Bracket for CB antenna / radio antenna for CargoBear system roof rack Stainless steel, black powder-coated.Delivery without antenna, price per piece.- Suitable for all CargoBear 1 + 2 roof racks!

Radio 90 CB antenna for fixed mounting Technical data:  Length approx. 90 cm 200 W 4 m cable with DV plug 1/4 lambda The antenna has an open-ended cable to make it easier to lay the cable. A PL259/6 plug for RG58 coaxial cable is required for connection to a radio.