ROADspec TDCI Puma Including adapter and valve adapter Clutch slave cylinder The ROADspec clutch is specifically designed for your daily road-going Defender with 2.4l or 2.2l Puma engine. If you do a bit of towing now and then, perhaps some light off-roading or just use your Landy as a commuter, then the ROADspec has everything you need to keep you going for years to come. It’ll even take mildly tuned motors that have a little more poke than standard! And by the way, the pedal weight is not heavier than the original. This kit includes the release bearing and concentric slave cylinder unit Description:  LOF HD friction material High torque sprung center hub G90 high-temp assembly grease Updated 2.2l genuine release bearing/slave cylinder Pedal weight not heavier than original If you have a 2.4l engine and have not changed to the updated release bearing and slave cylinder then you will need this bleed valve and adapter. SET consists of: ROADspec coupling TD4 Adapter Valve adapter for clutch cylinder You can find more products for improved clutch performance here: clutch spring Note from LOF: if this clutch is newly installed, the LOF Powermaster clutch master cylinder should not be installed as well. We recommend replacing the pilot bearing when replacing the coupling.

Defender Clutch Master Cylinder It’s easy to forget these days but driving used to be real work. And you don’t have to go back to the days of double clutching or starter cranks either. Even the Defender got more and more user friendly and less work over the years, with power steering and electric windows making it easier on the arms. But especially with TD5s and older, your left leg still has to work a lot harder with the clutch than the right leg with the gas pedal. In low range off-road, when maneuvering a trailer or even in stop-and-go traffic in the city, the physical effort and strain can become very noticeable, not only for older, smaller or female drivers. Our new POWERmaster cylinder reduces the weight of the clutch pedal by 30 % when compared to the standard Girling master cylinders with OEM part number STC500100. The replacement of the master cylinder takes about 25 minutes, detailed instructions are provided. If you are looking for even higher weight reductions in the pedal, this additional pedal assist spring might be the answer. "LOF does not recommend the installation: for newly installed clutches in combination with the LOF Power slave cylinder

Clutch Slave Cylinder for LR Land Rover Defender and Discovery 2 Td5/TDI R380 for all 300TDI and TD5 engines in all Defenders and Discovery 2 with a manual transmission (R380)

saving bundle: Heavy Duty clutch kit incl. Improved MT82 intermediate shaft for TD4 saving bundle consisting of automatic clutch, friction disc, release bearing, matching clutch slave cylinder and a reinforced intermediate shaft MT82 transmission. For TD4 built in 2007-2016 Information about the clutch automat with friction disc, release bearing and clutch slave cylinderEspecially with switching operations under higher load, such in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, specially adapted to the Defender Td4, eliminate the familiar problems of clattering or jamming clutches. Another, but less common, problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive! The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Information on the reinforced intermediate shaft for MT82 transmissions.Improved intermediate shaft for MT82 transmission in Land Rover Defender TD4 / TDCi / Puma 2.4 / 2.2 Known problem: The intermediate shaft of the TD4 / TDCi / Puma 2.4 / 2.2 models is not greased and is not supplied with oil. The connection of the two-piece intermediate shaft wears after prolonged use, since the shaft with outer ring gear has direct contact with the shaft with inner ring gear. In the worst case, this wear ensures that the sprocket shears off and the vehicle thus stops. A regular lubrication of the sprocket helps, but is in the long run very cumbersome Our solution: The improved intermediate shaft is supplied with the oil of the gearbox and thus prevents the wear of the shafts. Easy and uncomplicated! We recommend replacing the pilot bearing when replacing the coupling.

Heavy Duty Clutch Kit for Land Rover Defender TD4 Especially with switching operations under higher load, such. in trailer operation or in performance-enhanced vehicles, enormous forces must be transmitted by the clutch. A common problem with the Defender's original clutch is the failure of the insufficiently sized torsion springs. The torsion springs, which are specially adapted to the Defender Td4, eliminate the familiar problems with clattering or jamming couplings. Another, but less common problem is the ingress of oil from the engine or transmission into the clutch bell. This oil is absorbed by the porous friction linings and occurs during driving by the resulting frictional heat repeatedly to the friction lining. Due to the reduced traction it comes in the episode to a higher heat development and vitrification of the coverings. The heat is a measure of the converted energy that is no longer available to the drive!The organic coating used in this coupling can not absorb oil and therefore does not vitrify. It convinces with specially adapted friction modifiers with a soft response and enables a 100% adhesion. Of course, the pads are asbestos- and lead-free, free of other toxic heavy metals and heavy metal compounds. Complete set consisting of automatic clutch, friction disc and release bearing. Clutch kit with clutch slave cylinder for Defender TD4 from year of construction 2007-2016 We recommend replacing the pilot bearing when replacing the coupling.