OptiMATE solar kit, panels with intelligent charge/monitoring controller. The highly effective solar charger (solar impulse charging system), with which even deeply discharged batteries can still be saved and protected. It guarantees safe and intelligent charging, as the OptiMATE solar battery charging system independently switches between continuous charging or pulse charging depending on the sunshine. OptiMATE analyses the state of the battery the next day and optionally continues charging or - in the case of a defective battery - optimisation. Safe long-term maintenance without the risk of overcharging. Automatic shutdown in the event of a short circuit or as soon as the battery is disconnected. Excellent safety for battery and vehicle electronics Easy monitoring of the battery status with the help of the monitor display, which updates itself every 3 seconds. (current consumption < 0.5 mA). With this battery charging system you get an all-round package, mobile, portable, intelligent. The system is suitable for standard, AGM, LFP and gel batteries. It is supplied with battery terminals and ring eye connections and with German instructions. The solar systems are manufactured to a high standard in South Africa (made in South Africa). Product Information Solar Panels - Solar Charger Info about the solar panels: Power: 40 watts (max.)60 Watt (max.)80 watts (max.) Voltage: 12 V nominal, 22 V maximum Possible uses: Outdoor/indoor Design: High-quality aluminium frame (weatherproof) with 4 mounting brackets, output cable 200 cm with SAE connector Info about the OptiMATE charging/monitoring controller: Charging current:  3.3 A from 40 W panel (max. average current), 3-5 A pulse current. 5 A from 60 W panel (max. average current), 3-5 A pulse current 6.67 A from 80 W panel (max. average current), 3-5 A pulse current Usage: Indoor/outdoor (lowest temperature: -20 °C. Economy mode: start with low 1 V voltage Suitable for: STD, AGM and GEL 12 V batteries with 2 - 240 Ah. Input: 15 - 22 V Design: Weatherproof charge controller housing with mounting holes and loops (for Velcro or Ziptie). SAE input connector for solar panel and output cable of 100 cm to be connected to the battery with the supplied weatherproof battery cable and standard battery clamp set. Dimensions (corner brackets included): 40 watt panel: width: 42.9 cm / 16 7/8 " height: 68.6 cm / 27 " depth: 3.3 cm / 1 1/4 "60 Watt panel: Width: 65.9 cm / 16 7/8 " Height: 68.6 cm / 27 " Depth: 3.3 cm / 1 1/4 "80 Watt panel: Width: 68.5 cm / 27 " Height: 78.1 cm / 30 3/4 " Depth: 3.3 cm / 1 1/4 " Optimum safety: there is no risk of overcharging. Completely safe for vehicle electronics. Spark suppression. Safe for long-term battery maintenance. Automatic cut-off in case of short circuit or disconnected battery. The panels are supplied with a 3 m cable as standard. A suitable extension cable can be found here. Additionally included in delivery are: suitable carrying bag adjustable stand (fixed to the panel) The panel is ideally suited for our parking heater, for example. Please note: When using the panel for a cool box, a buffer is necessary, as the starting current is too high.  Made in South Africa https://www.youtube.com/user/TecMate1/about  <iframe width="560" height="315" src="https://www.youtube.com/embed/lYjy11Jk6JU" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

Product description The Monitor consist of a special Bluetooth connector (S-BC), which delivers, in combination with the Votronic solar charger (MY2013) with the LCD solar computer S, or with the smart Shunt with the LCD battery computer S or the VPC Jupiter, all the information from your monitor to your phone. The corresponding app for Android and IOS is available in both stores. Connecting the Bluetooth module S-BC is incredibly easy. Simply use the included cable to install it between Votronic solar charger and LCD solar computer S or between Smart Shut and the LCD battery computer s / VPC Jupiter. The device has two in- and out-puts, this way you can connect 1 solar charger with LCD solar computer and 1 Smart Shunt with LCD battery computer or VPC Jupiter simultaneously. This way you get all the information on charging, voltage, solar-status, etc. right on your phone without any trouble. Additionally, the app saves the most important data and displays it in the app for extended periods of time. You can even export these files for analysis purposes. This Bluetooth module can just as well be installed after the fact, so whenever you are ready! Technical specifications:  Typ Bluetooth Connector S-BC  Measuments (WxLxH) in [mm] 75 x 47 x 24  Weight in [g] 37  Certifications CE, E-Prüfung (EMV/Kfz-Richtlinie)  Surroundings: Humidity: max. 95%  Scope of delivery: Manual, 2x Cable 6-point connector 1 m long The Bluetooth-Connector S-BC is compatible with the following devices: VOTRONIC Solar-charger in SR- and MPP-technology from 2014 (serial number 14Vxx.xxxxx) Battery Charger, Typ VBCS-Triple LCD battery computer S with Smart-Shunt VPC Jupiter with Smart-Shunt Energy Monitor App via Bluetooth-Connector S-BC        Compatible with LCD-Batterie-Computer S and VPC Jupiter with Smart-Shunt    Compatible with Votronic Solar-charger(SR and MPP) from 2014 with LCD-Solar-Computer S    Solar- and battery-Information thanks to a shared module (Dual-Mode)    Plug & Play    Upgrade any time    Compact form-factor and minimal energy consumption    Connection via Bluetooth 4.0 (2,4 GHz)    Range up to 50 m    Free App (Android and IOS)    Export CSV.files for analysis Android from Android 5.0IOS from iOS 10: iPhone ( 5) or iPad (3. Generation)

The following values ​​are calculated and displayed under microprocessor control: - Current solar power 0 - 999 W (watt) - Current solar power 0 - 60.0 A (ampere) - The geographic and weather-dependent influences show up immediately and unmistakably. This also applies to the orientation of the sun, partial shading or soiling of the solar modules. - Current solar battery voltage 7 - 32.0 V (volts) Allows conclusions to be drawn about the battery status (flashing warning display at under or Overvoltage of the battery) - Invited solar capacity 0 - 9999 Ah (ampere hours) - Invited solar energy 0 - 9999 kWh (kilowatt hours) The energy generated by the solar modules (Wh and kWh) and that charged into the battery Capacity (Ah) are measured, added up and displayed, even over days and weeks. The display values ​​can be individually reset to "zero" at any time for your own statistical purposes: Are the solar modules shaded or dirty or is something wrong? How much energy does my solar system actually deliver?In order to be able to answer these questions, VOTRONIC offers the LCD solar computer S, which is simply connected to the VOTRONIC solar charge controller of the SR and MPP series and immediately provides the required information. It is also possible to connect the LCD solar computer S to the controller at a later date, since the VOTRONIC solar charge controller already has are ready to plug in and provide the required signals. The connection is therefore kept extremely simple. The measured values ​​are clear and easy to use at the push of a button for better control and use of the solar system shown on the display. The display is backlit (switchable) and also from greater distances and very easy to read under lighting conditions. The LCD solar computer S is designed as a panel version to match the VOTRONIC module system and is both optically and also mechanically (uniform height 85 mm) to the other display modules. Small front panel dimensions and the particularly small installation depth of just 22 mm allows installation at almost any point. If the device is not installed countersunk, stands a corresponding add-on housing is available in our range of accessories. The connection to the solar controller is ready to plug in with the supplied 5 m long connection cable, which can be extended by a further 5 m. Technical specifications: Nominal battery voltage (DC) in [V] 12 and 24 Current consumption max. in [mA] 3 - 30 LC display with specific segments Display function W, A, V, Ah, Wh Measuring range 20 - 990 Dimensions (WxHxD) in [mm] 80 x 85 x 25 Installation dimensions (WxHxD) in [mm] 66 x 72 x 22 Weight in [g] 55 Approval marks CE, E-approval (EMC / vehicle directive) Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: 5 m connection cable, fastening screws, operating instructions, drilling template

High charging capacity even on short journeys or full charge on longer journeys. The voltage is brought to the required level (increased or decreased) in order to be able to precisely charge the on-board battery with the optimal charging characteristic. Compensates for line losses and voltage fluctuations in the alternator, such as occur continuously to a considerable extent in Euro 6 vehicles (intelligent alternators). Compact design, low weight (high-frequency switch mode technology) and powerfully dimensioned power components for safe operation. A significantly better energy balance of the on-board battery without intervention in the starting circuit If the 12 V consumers are supplied, they are protected against overvoltage and voltage fluctuations. Overcharging of the battery is impossible because the charging voltage is regulated in such a way that it is free of peaks Fully automatic operation: the device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. The batteries are not discharged when the engine is not running. Parallel and buffer operation: If the battery is used at the same time, it continues to be charged or is kept full. The device automatically calculates and monitors the adjustment of the charging times. Monitoring-free charging: Multiple protection against overload, overheating, overvoltage, short circuit, malfunction and back-discharge of the battery through electronic regulation up to complete separation of device and battery. Built-in on-board network filter: Problem-free parallel operation with other charging sources (EBL, chargers, motor and fuel generators, solar systems) on one battery. Charging cable compensation: voltage losses on the charging cables are automatically compensated. Connection for battery temperature sensor (included in delivery): In the case of lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, results in better full charging of the weaker battery in the cold, and in summer temperatures unnecessary battery gassing avoided. LiFePO4 batteries: battery protection at high and especially at low temperatures <0 ° C. Charging aid for deeply discharged lead batteries: Gentle pre-charging of the (lead-acid, gel, AGM) battery up to 8 V, then powerful support for the battery if consumers are still switched on. Technical specificationsInput from vehicle starter battery "+ IN Start"Vehicle starter battery nominal voltage 12 V.Battery capacity (size), recommended at least 50 AhInput voltage range (EURO 6 +), D + controlled 10.5 - 16.5 V.Input overvoltage shutdown (EURO 6 +), max. 16.5VPower consumption max. 490 WCurrent consumption (at lowest input voltage) max. 0.05 A - 39 AActivation control input "D +", from D +, terminal 15, ignition 8 - 17 V.Charge output on board supply battery "+ OUT board"Charge / buffer / load current, regulated IU1oU2, lead, LiFePO 0 A - 30 A (0 A - 20 A *)Lead-acid, gel, AGM battery nominal voltage 12 V. Capacity (battery size), recommended / up to 60-200 / 260 Ah Lead loading programs stored in the memory 3 Precharge current (deeply discharged battery <8V), max. 15 A (10 A *) Safety charging voltage in the event of battery overtemperature 12.80 V.LiFePO4 battery nominal voltage 12 V (12.8 -13.3 V) Capacity (battery size), recommended / up to 60-200 / 260 Ah LiFePO4 charging programs stored in the memory 4 Safety charging voltage in the event of battery overtemperature 12.80 V.Recharging branch, charging / charge retention for the 12 V START batteryfrom the BOARD battery (e.g. when charging the BOARD battery from the mains) 12 V / 0-1 AActive with lead acid, gel, AGM BORD battery voltage On:> 13.1 V, Off: <13.0 VActive with LiFePO4-BOARD battery voltage on:> 13.5 V, off: <13.4 V"T T" input for battery temperature sensor "board" yesEBL START In, EVS measurement input: yesQuiescent current, StandBy 3 ... 7 mATriple charging timerVoltage ripple <30 mV rmsCharging voltage limit "+ OUT board" (consumer protection) 15.00 VExternal overvoltage shutdown "+ OUT board" (20 sec) 15.50 VShort circuit / back discharge / S. Loaders 1 "Gel": charging program for gel batteries, characteristic curve IU1oU2Matched to closed, gas-tight gel / dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation". 2 "AGM": Charging program for AGM / fleece batteries, characteristic curve IU1oU2Designed for charging closed, gas-tight AGM (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charge and then a moderate U2 level to maintain charge (Plate and round cell technology). 4 "UNIVERSAL": Charging program for lead-acid / wet / AGM batteries, characteristic curve IU1oU2Universal program for charging and maintaining the charge of acid batteries in vehicles (mixed mobile / stationary). With a medium U1 level, it still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. Li "LiFePO4": Charging program for lithium batteries, characteristic IU1oU2Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuit.

The most modern 12 V 10 A & 24 V 5 A battery charger in the world! OptiMate 7 12 V-24 V is perfect for 12 V and 24 V starter and deep-cycle batteries requiring accurate temperature-controlled charging and unmonitored, safe long-term expectancy. SPECIAL FEATURES: Tailored to sensitive electronics: The RETTUNGS program is designed to provide a SAFE, fully automatic, low voltage start (starting at 0.5 volts) and IMPULS rescues of deeply discharged batteries connected to very sensitive electronics, such as light aircraft, industrial equipment, etc , Protection against Wrong Voltage Selection: When 24V has been selected and a 12V battery is connected, OptiMate 7 12-24 V immediately warns that a lower voltage has been measured and will not continue charging. The USER must confirm that the rated voltage of the connected battery is 24 V before the RESCUE mode is activated. CHARGING POWER: 10A @ 12 V / 5 A @ 24 V (Ampmatic) USE: Indoor / outdoor (lowest temperature: -40 ° F / -40 ° C). RESCUE: Starting at low voltage of 0.5 V (12 V) + 1-stage desulphation rescue. IDEAL FOR: STD, AGM & GEL 12 V batteries from 3-400 Ah / 24 V batteries from 1-200 Ah. INPUT: Global (100-240 V 50-60 Hz), high efficiency (CEC listed), fully enclosed. DESIGN: Weather resistant housing with wall mount, with 6 ft / 180 cm power cable and 6 ft / 180 cm charging cable with SAE plug. Weather resistant battery lead & standard battery terminal set included. 6 different charging programs: 12 V: 14.4 V (for normal lead acid batteries) 12 V: 14.7 V (for high performance AGM or spiral cells – OptiMa / odessey batteries)12 V: 15 V (for Ca/Ca batteries that need 15 V charge). 24 V: 28.8 V (for normal lead acid batteries) 24 V: 29.4 V (for high performance AGM or spiral cells – OptiMa / odessey batteries)24 V: 30 V (for Ca/Ca batteries that need 15 V charge). SAFE: No risk of overcharging. Absolutely safe for the vehicle electronics. Radio suppression. Safe for long-term battery maintenance. Automatic shutdown in case of short circuit or disconnected battery. https://www.youtube.com/user/TecMate1/about

High performance diagnostic charger with test function for LiFePO4 and LFP batteries. Ideal for charging 12.8 V-13.2 V LiFePO4 and LFP high performance batteries with a capacity of 2.5 to 120 Ah. Special advantages: The TUNE mode provides a stable power supply when reprogramming vehicle systems, in car showroom displays, and when saving settings when battery cables need to be disconnected to accommodate power-driven accessory systems or when replacing batteries. BMS Reset and Button Activation - for batteries with resettable low voltage / deep discharge protection. BMS Reset Battery SAV mode: starts at 0.5 V with continuous monitoring and checking of defective or shorted cells; also the charge acceptance can be verified. Unnecessary (and unsafe) charging of a defective battery is prevented. SafeTº: automatic adjustment of the charging current to the ambient temperature determined by the charger. Reduced charging below freezing. Do not charge at temperatures below -20 ° C (to avoid damage to lithium batteries). AmpMatic: Microprocessor-controlled adjustment of the charging current to the ideal charging curve for LiFePO4, matching the battery size / condition, to achieve the fastest possible and complete charge. Technical specifications: CHARGING POWER: 9.5 A (AmpMatic) USE: Indoor / outdoor (lowest temperature: -20 ° C. SAVING MODE: Low Voltage Start at 0.5 V + 3-step Low Voltage SPAR and TEST mode SUITABLE FOR: LiFePO4 (LFP) 4 batteries with 2 to 120 Ah INPUT: global (100 to 240 V, 50 to 60 Hz), high efficiency (CEC listed), fully sealed DESIGN: weatherproof housing with wall mount, with 152 cm power cord and 180 cm charging cable with SAE connector SAFE: No risk of overcharging. Absolutely safe for the vehicle electronics. Radio suppression. Safe for long-term battery maintenance. Automatic shutdown in case of short circuit or disconnected battery. 3-year limited warranty. https://www.youtube.com/user/TecMate1/about

Battery box with various connections, with solar panel Optionally with AGM or LiFePo battery In the 21st Century modern technology is everywhere, even off-road and off the grid, but more often than not there is no power when you're out and about on some trail in some country. One option is the classic cigarret-lighter as a power source, but in using this frequently you risk decharging your battery to a point where it won't start your car anymore. Another option would be a generator, but those are loud, impractical and noisy. To solve this probem highly portable powerbanks were invented, but for a multiple day long trip a small powerbank just won't cut it. So, what if you had a lagre but portable power bank? One you could simply charge, even off the grid, maybe with a solar panel? And one that is heavy dut enough to endure week long trips and years of use ?  Hold on, that's exactly what we did! This compact, but long-lasting Powerstation (33Ah) offers a cigaret lighter-output and two USB-ports (5V - 2.1A), in a roubust shell. It can simply be charged using our solar panels by Optimate. LiFePo4 batteries – with their lithium iron phosphate cathode material – are perfect for running your camping or work utilities on the road, especially in conjunction with our mobile battery boxes. Unlike your conventional AGM lead-acid technology, the lithium battery combines vastly superior charging/discharging qualities with extremely low weight and small volume, respectively, and a long service life. LiFePo4 batteries tolerate deep discharging without problems, unlike AGM batteries which will suffer irreparable damage when repeatedly discharged beyond 50%. Unless you require the greater tolerance for extreme cold in AGM’s, you should definitely consider the higher initial costs of LiFePo4 batteries and compatible chargers. Enormous weight and space reductions, the long life-cycle and the hassle-free charging and discharging of the battery are strong arguments for the investment. And last but not least: LiFePo4-technology is extremely safe. robust shell portable design comfortable handle 20 A car-fuse 33 Ah (396Wh) AGM brand battery optionally 35 Ah LiFePo battery 2x USB-plug (out) 1x cigaret-lighter (out) 1x SAE junction box for charger (charger not included) (in) 1x On-/Off-switch  simply plug in and off you go Scope of delivery: 1 x Optimate solar panels in a choice of 40, 60 and 80 watts, including bag and stand.1 x Optimate charge/monitor controller, including weatherproof battery cable1 x Nakatanenga battery box selectable in 4 colours, with different connections