LED - Reversing light Product information:     LED-LIGHT    PRC7263LED    Reversing lightVehicle:    Defender - 1987 - 2006    Series 3

Adaptor Plate for Brake- and Fog-Lights -  Land Rover Defender previous to Model year 1998 This adaptor (1 piece) allows you to mount round breaklights and fog lights to older Defender models (previous to MY1998). This plate is compatible with your standard lights and our own LED lights.

LED signal light Land Rover Defender: rear fog light, smoke gray High-quality LED rear fog light for the Land Rover Defender in visually appealing smoke gray / smoke. The signal light has an E-mark and a diameter of 95 mm. Including SuperSeal connector 2-pin. If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to fit the new round rear fog lights. As a rule, the original drill holes can then be used. Please note that you can also purchase this rear fog light with other signal lights in a bundle with a price advantage: LED signal lights for Land Rover Defender. Please note: The screws must not be overtightened (only hand-tight!), otherwise the plastic housing may crack. These cracks could allow water to penetrate the generally waterproof lights. Only use a screwdriver and NOT a cordless screwdriver!    

This high-quality LED tail light / brake light is for the Land Rover Defender. It has an E-mark, a diameter of 73 mm and impresses with the unique smoke grey color. Please note that you can also purchase the tail light / brake light with additional signal lights as a bundle with a price advantage: LED signal lights for Land Rover Defender. Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!

LED signal lamps for Land Rover Defender, smoke grey The advantages of LEDs are well known: low power consumption, strong light output, vibration resistance and a long lifetime. In this smoke grey signal lamp set for the Land Rover Defender (Series III, Defender 90, Defender 110, Defender 130) the following LEDs are included: The standard-set with 8 bulbs contains: 2x front indicatior ligths 2x front position lights, either with or without day-driving light 2x rear indicators 2x brake/rear lights adjustable indicator relay The set with 9 bulbs additionally (aditionally to the standard-set) contains:  1x tailgate break light The set with 10 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light and 1x reverse light→ OR 2x wing side indicators The set with 11 bulbs additionally (aditionally to the standard-set) contain:  → 1x fog light, 1x reverse light and 1x tailgate break light→ OR 2x wing side indicators The set with 12 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light and 2x wing side indicators The set with 13 bulbs additionally (aditionally to the standard-set) contains:→ 1x fog light and 1x reverse light, 2x wing side indicators and 1x tailgate break light Note that indicators must be orange by law. All bulbs come with E-approval so that they can be fitted without further TUV recording. All bulbs come with correct plugs for simple replacement for vehicles from MY 1998 (TD5 und TD4). Fittings are supplied and also an adjustable indicator relay that even allows to adjust indicator speed. Older vehicles can be retrofitted after removing the plug. This requires soldering. If the lamps on the existing vehicle are square at the rear, you need 1x AMR3850 mounting base per lamp to mount the new round reversing lights. As a rule, the original drill holes can be used. This signal lights kit is the ideal addition to our 7" Bi-LED main headlights, the LED license plate light and any additional LED spotlights - this brings the Land Rover Defender into the 21st century light-wise! Please note: The screws must not be over tightened (only hand-tight!), Otherwise the plastic housing may crack. These cracks could allow water to penetrate into the generally watertight luminaires. Use only a screwdriver and NO cordless screwdriver!