Solar panel for bonnet Next generation solar cells are increasingly integrated into structural components. Instead of separate, awkwardly mounted modules on the roof of a house, for example, the roof tiles themselves function as solar panels. Our PV modules for the hoods of 4x4s and vans follow this principle. While they do not yet replace the hood, they are so thin (only 3 mm) and so flexible that they precisely fit the shape of the hood – making them hard to recognize as an extra add-on. In addition, they are also extremely aerodynamic and robust enough to even step on them if needed. The hood modules for Defenders Td5 and Td4, New Defender, Jimny 2, Mercedes G-Class and Sprinter have an output of between 75 and 90 W at 12 V, depending on the model. Your only requirement is sufficient sunlight to generate enough power for the primary and secondary batteries in the car during the day. This in turn enables you to reliably operate all the devices needed in a camper or expedition vehicle: navigation and communication devices, laptop, cooking equipment, refrigerator and much more. Your equipment always remains fully functional and a sufficient charge of the starter battery is also guaranteed. Mounting the PV module and wiring it up to the batteries in the vehicle are equally easy DIY jobs. The included adhesive tape is all you need to attach the panel to the hood while the intelligent charge controller and the adapter allow for plug & play electric installation. Note: as the connection is individual, the power cables may have to be extended.

OptiMATE solar kit, panels with intelligent charge/monitoring controller. The highly effective solar charger (solar impulse charging system), with which even deeply discharged batteries can still be saved and protected. It guarantees safe and intelligent charging, as the OptiMATE solar battery charging system independently switches between continuous charging or pulse charging depending on the sunshine. OptiMATE analyses the state of the battery the next day and optionally continues charging or - in the case of a defective battery - optimisation. Safe long-term maintenance without the risk of overcharging. Automatic shutdown in the event of a short circuit or as soon as the battery is disconnected. Excellent safety for battery and vehicle electronics Easy monitoring of the battery status with the help of the monitor display, which updates itself every 3 seconds. (current consumption < 0.5 mA). With this battery charging system you get an all-round package, mobile, portable, intelligent. The system is suitable for standard, AGM, LFP and gel batteries. It is supplied with battery terminals and ring eye connections and with German instructions. The solar systems are manufactured to a high standard in South Africa (made in South Africa). Product Information Solar Panels - Solar Charger Info about the solar panels: Power: 40 watts (max.)60 Watt (max.)80 watts (max.) Voltage: 12 V nominal, 22 V maximum Possible uses: Outdoor/indoor Design: High-quality aluminium frame (weatherproof) with 4 mounting brackets, output cable 200 cm with SAE connector Info about the OptiMATE charging/monitoring controller: Charging current:  3.3 A from 40 W panel (max. average current), 3-5 A pulse current. 5 A from 60 W panel (max. average current), 3-5 A pulse current 6.67 A from 80 W panel (max. average current), 3-5 A pulse current Usage: Indoor/outdoor (lowest temperature: -20 °C. Economy mode: start with low 1 V voltage Suitable for: STD, AGM and GEL 12 V batteries with 2 - 240 Ah. Input: 15 - 22 V Design: Weatherproof charge controller housing with mounting holes and loops (for Velcro or Ziptie). SAE input connector for solar panel and output cable of 100 cm to be connected to the battery with the supplied weatherproof battery cable and standard battery clamp set. Dimensions (corner brackets included): 40 watt panel: width: 42.9 cm / 16 7/8 " height: 68.6 cm / 27 " depth: 3.3 cm / 1 1/4 "60 Watt panel: Width: 65.9 cm / 16 7/8 " Height: 68.6 cm / 27 " Depth: 3.3 cm / 1 1/4 "80 Watt panel: Width: 68.5 cm / 27 " Height: 78.1 cm / 30 3/4 " Depth: 3.3 cm / 1 1/4 " Optimum safety: there is no risk of overcharging. Completely safe for vehicle electronics. Spark suppression. Safe for long-term battery maintenance. Automatic cut-off in case of short circuit or disconnected battery. The panels are supplied with a 3 m cable as standard. A suitable extension cable can be found here. Additionally included in delivery are: suitable carrying bag adjustable stand (fixed to the panel) The panel is ideally suited for our parking heater, for example. Please note: When using the panel for a cool box, a buffer is necessary, as the starting current is too high.  Made in South Africa https://www.youtube.com/user/TecMate1/about  <iframe width="560" height="315" src="https://www.youtube.com/embed/lYjy11Jk6JU" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

Please note that the solar charge controller can only be used with solar panels up to the maximum power rating (Wp) and below the maximum allowable voltage (Voc) may be used. The controller is not intended for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supplies, batteries or other power sources. The MPP solar controller for high-quality motorhomes, caravans and boats. Votronic solar controllers of the "MPP" series (Maximum Power Point) with “IU1oU2” charging characteristics are connected as a link between the solar panel (s) and the battery (s). With MPP technology, the controller automatically determines the maximum power output (MPP) several times per second the solar modules. The excess voltage of the solar module is transformed to a higher charging current for the battery, (realized by high-frequency switching regulator technology with high efficiency). The gain in charging current is used for shorter Charging times taken care of and for the best possible use of the solar system. The MPP solar controllers work fully automatically, are maintenance-free and offer the following functions: MPP charging current increase compared to conventional controllers through the use of the latest controller technology (microprocessor) by 10% to 30% (efficiency> 95%). The performance plus is particularly evident in the cooler seasons and z. B. in high fog, lower and diffuse lighting (overwintering). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, Balancing, safety circuit and approval!) Of the specified nominal voltages and the additional supply of an Consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is impossible. Two battery charging outputs: Automatic charging of the main supply board battery (BORD I) as well as support charging and charge retention (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: standard protection against overload, overheating, polarity reversal and battery back-discharge (with insufficient solar power z. B. twilight, at night etc.). Parallel / buffer operation: compliance with the charging regulations even when consumers are operating at the same time. Overcharge protection: regulates the charging current of the battery when there is too much solar power and the battery is full, ensures Power consumption through immediate recharging for the highest possible battery charge. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid layers (lead) and ensures equalization charging of the individual battery cells (lead and lith.), then automatic maintenance charging (U2). Charging cable compensation: voltage losses on the charging cables are automatically compensated. On-board network filter: problem-free parallel operation with wind and motor generators, network chargers, alternators, etc. Measurement output for EBL, possibly existing electroblock in the living area of ​​the vehicle: Enables the convenient use of a (Solar) power display built into the electroblock to control the solar system. Please check in advance the compatibility of your Schaudt electroblock (EBL) and the corresponding control and scoreboard, as we cannot guarantee this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): causes permanent abundant solar The automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation. Connection for battery temperature sensor (item no. 2001): With lead batteries, the adjustment takes place automatically the charging voltage to the battery temperature, causes a better full charge of the weaker battery in the cold, In summer temperatures, unnecessary battery gassing and stress is avoided. LiFePO4 batteries: battery protection at high and especially at low temperatures. If the battery temperature can drop below 0 ° C during operation. Ready to plug in for the connection of the Votronic solar display devices LCD-Solar Computer S for optimal control of the system. Technical data CHARGE REGLER-MPP250: Nominal battery voltage (AC) in [V] 12Solar module output max. [Wp] 250Solar module current max. [A] 15.0Solar module voltage max. [V] 50Charging current batt. I / II max. [A]  Load programs: 1 "Gel": charging program for gel batteries, characteristic curve IU1oU2Matched to closed, gas-tight gel / dryfit batteries with fixed electrolyte, which generally require a higher charging voltage level and longer U1 holding times in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation". 2 "AGM": Charging program for AGM / fleece batteries, characteristic curve IU1oU2Designed for charging closed, gas-tight AGM (Absorbent-Glass-Mat) batteries in lead-fleece technology, which require a particularly high U1 level with coordinated holding times for full charge and then a moderate U2 level to maintain charge (Plate and round cell technology). 4 "UNIVERSAL": Charging program for lead-acid / wet / AGM batteries, characteristic curve IU1oU2Universal program for charging and maintaining the charge of acid batteries in vehicles (mixed mobile / stationary). With a medium U1 level, it still offers short charging times, a good charge factor and good acid mixing for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy-duty batteries, as well as AGM batteries with a normal U1 level. Li "LiFePO4": Charging program for lithium batteries, characteristic IU1oU2Charging program tailored to lithium LiFePO4 batteries with their own BMS and prescribed or built-in protective circuit.

Accessories for OptiMATE solar battery charging systems Product Informations Extension cable with a length of 4.6 m with SAE connection Length = 15 ft / 460 cm 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -20 ° C / -4 ° F Use at very low temperatures SAE built-in socket Length = 100 cm / 40 " Front mounting, rear mounting, for sheets from 1 mm / 0.040 "thickness 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -40 ° C / -40 ° F Use at very low temperatures; stays flexible at temperatures below freezing SAE built-in socket (short cable) Length = 15 cm / 6 " Front mounting, rear mounting, for sheets from 1 mm / 0.040 "thickness 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -40 ° C / -40 ° F Use at very low temperatures; stays flexible at temperatures below freezing Plug with rotary adapter, fits on Ø 12 mm MOTORCYCLE / DIN or Ø 21 mm AUTO sockets, with 2-pin SAE connection according to industry standard Length = 20 ″ / 50 cm Industry standard 2-pin SAE connector 8 A fuse (in the plug) Max. Cable values: 5 Amp -20 ° C / -4 ° F Use at very low temperatures With rubber cable gasket for OptiMate heavy-duty SAE connection. Y splitter, SAE IN to 2 x SAE OUTBranching your permanent battery supply line, creation of SAE outputs. Length = 12 ″ / 30 cm Industry standard 2-pin SAE connector. Max. Cable values: 5 Amp -20 ° C / -4 ° F use at very low temperatures With line seals and sealing end caps for OptiMATE heavy-duty SAE connections. https://www.youtube.com/user/TecMate1/about

Practical dynamo / solar flashlight This little flashlight belongs in every emergency or survival kit. Even when the in-built battery is completely flat, you can get it working in no time, because the power sources for this little helper are built into the lamp’s housing: a small solar panel on one side and a dynamo with a crank handle on the other. Simply recharge this torch by exposing the mini solar panel to sunlight or by exerting a tiny amount of physical labor i.e. cranking the handle. There is no need for any external sources of electricity, chargers or replacement batteries. This combination of hassle-free recharging makes this torch ideal in all kinds of off-grid or emergency scenarios: for camping, when your car breaks down at night or in a black-out. Or simply when walking alone or with your dog at night. The lamp‘s three economical LEDs can be powered for approximately 1 hour by only 6 minutes of cranking. If possible, you can also keep the torch in a place where it can regularly collect sunlight. In which case, you’ll probably hardly ever need to use the crank handle. The black and olive housing is compact, robust and features an integrated carabiner hook to securely hang the torch from your belt, a backpack or in your tent. The ergonomic design ensures, that all functions can be quickly accessed, even in the dark. This inexpensive flashlight comes with a 1-year manufacturer’s warranty. Dimensions:124×45×32 mm

OptiMate Solar DUO charges and maintains ChargeSaves dead batteries from 4 V with its unique pulse charge.The fastest charge is delivered as the "intelligent charge control" selects between pulse and continuous charging depending on sunlight strength. Intelligent maintenance continues the next day if the battery has maintained the charge overnight, otherwise the program returns to the OPTIMIZE step. MONITORINGBattery status is displayed every 3 seconds. Ready indicator for STD, Hi-Performance AGM and Lithium LEP batteries. Draws less than 0.5mA during monitor mode.Automatically switches to CHARGE when solar power is sufficient. MOUNTINGThe OptiMate DUO charge and monitor controller is separate from the solar module and can be mounted near the vehicle or battery for easy tracking of charge and maintenance progress. The solar panel must be mounted and angled to receive direct sunlight. The range / distance between the battery and the panel is 315 cm / 124″. To extend, use OptiMate cable extensions O-03, O-13 or O-23 and insert them between the solar panel and the OptiMate DUO charging monitor. Application noteFor further application information please refer to the product data sheet

Product description The Monitor consist of a special Bluetooth connector (S-BC), which delivers, in combination with the Votronic solar charger (MY2013) with the LCD solar computer S, or with the smart Shunt with the LCD battery computer S or the VPC Jupiter, all the information from your monitor to your phone. The corresponding app for Android and IOS is available in both stores. Connecting the Bluetooth module S-BC is incredibly easy. Simply use the included cable to install it between Votronic solar charger and LCD solar computer S or between Smart Shut and the LCD battery computer s / VPC Jupiter. The device has two in- and out-puts, this way you can connect 1 solar charger with LCD solar computer and 1 Smart Shunt with LCD battery computer or VPC Jupiter simultaneously. This way you get all the information on charging, voltage, solar-status, etc. right on your phone without any trouble. Additionally, the app saves the most important data and displays it in the app for extended periods of time. You can even export these files for analysis purposes. This Bluetooth module can just as well be installed after the fact, so whenever you are ready! Technical specifications:  Typ Bluetooth Connector S-BC  Measuments (WxLxH) in [mm] 75 x 47 x 24  Weight in [g] 37  Certifications CE, E-Prüfung (EMV/Kfz-Richtlinie)  Surroundings: Humidity: max. 95%  Scope of delivery: Manual, 2x Cable 6-point connector 1 m long The Bluetooth-Connector S-BC is compatible with the following devices: VOTRONIC Solar-charger in SR- and MPP-technology from 2014 (serial number 14Vxx.xxxxx) Battery Charger, Typ VBCS-Triple LCD battery computer S with Smart-Shunt VPC Jupiter with Smart-Shunt Energy Monitor App via Bluetooth-Connector S-BC        Compatible with LCD-Batterie-Computer S and VPC Jupiter with Smart-Shunt    Compatible with Votronic Solar-charger(SR and MPP) from 2014 with LCD-Solar-Computer S    Solar- and battery-Information thanks to a shared module (Dual-Mode)    Plug & Play    Upgrade any time    Compact form-factor and minimal energy consumption    Connection via Bluetooth 4.0 (2,4 GHz)    Range up to 50 m    Free App (Android and IOS)    Export CSV.files for analysis Android from Android 5.0IOS from iOS 10: iPhone ( 5) or iPad (3. Generation)

The following values ​​are calculated and displayed under microprocessor control: - Current solar power 0 - 999 W (watt) - Current solar power 0 - 60.0 A (ampere) - The geographic and weather-dependent influences show up immediately and unmistakably. This also applies to the orientation of the sun, partial shading or soiling of the solar modules. - Current solar battery voltage 7 - 32.0 V (volts) Allows conclusions to be drawn about the battery status (flashing warning display at under or Overvoltage of the battery) - Invited solar capacity 0 - 9999 Ah (ampere hours) - Invited solar energy 0 - 9999 kWh (kilowatt hours) The energy generated by the solar modules (Wh and kWh) and that charged into the battery Capacity (Ah) are measured, added up and displayed, even over days and weeks. The display values ​​can be individually reset to "zero" at any time for your own statistical purposes: Are the solar modules shaded or dirty or is something wrong? How much energy does my solar system actually deliver?In order to be able to answer these questions, VOTRONIC offers the LCD solar computer S, which is simply connected to the VOTRONIC solar charge controller of the SR and MPP series and immediately provides the required information. It is also possible to connect the LCD solar computer S to the controller at a later date, since the VOTRONIC solar charge controller already has are ready to plug in and provide the required signals. The connection is therefore kept extremely simple. The measured values ​​are clear and easy to use at the push of a button for better control and use of the solar system shown on the display. The display is backlit (switchable) and also from greater distances and very easy to read under lighting conditions. The LCD solar computer S is designed as a panel version to match the VOTRONIC module system and is both optically and also mechanically (uniform height 85 mm) to the other display modules. Small front panel dimensions and the particularly small installation depth of just 22 mm allows installation at almost any point. If the device is not installed countersunk, stands a corresponding add-on housing is available in our range of accessories. The connection to the solar controller is ready to plug in with the supplied 5 m long connection cable, which can be extended by a further 5 m. Technical specifications: Nominal battery voltage (DC) in [V] 12 and 24 Current consumption max. in [mA] 3 - 30 LC display with specific segments Display function W, A, V, Ah, Wh Measuring range 20 - 990 Dimensions (WxHxD) in [mm] 80 x 85 x 25 Installation dimensions (WxHxD) in [mm] 66 x 72 x 22 Weight in [g] 55 Approval marks CE, E-approval (EMC / vehicle directive) Ambient conditions, humidity: max. 95% room humidity, non-condensing Scope of delivery: 5 m connection cable, fastening screws, operating instructions, drilling template