Repair kit shift linkage / transfer case The transfer box on a Defender not only transmits the power from the engine two both axles, it also houses the middle diff lock as well as the reduction gearbox. The linkage connecting the transfer box to the low ratio/diff lock stick is naturally prone to heavy wear and tear. The repair kits give you the option to completely replace all worn bushes, bolts and the hexagon screw in the linkage. Nut, washers and SL retaining clips for the bolts are all included. Please note: Repair kit (REPSET-VEGE-LA) is compatible up to chassis-nr. LA999999 (ca. MY1994) Repair kit (REPSET-VEGE-MA) is compatible from chassis-nr. MA000000 (ca. MY1995)

Overhauled manual gearbox R380 for Defender TD5 and MT82 for Defender TD4   The R380 manual gearbox, which was installed in 4 revisions from 1998 to 2006 in the 300Tdi and Td5, among others, owes its name to the 380Nm input force for which the gearbox was originally designed. After initial teething troubles in conjunction with the LT230T transfer case and corresponding improvements, the reliable R380 was only replaced when European environmental regulations made it necessary to switch to the Td4 engine with its six-speed gearbox. We offer top-quality reconditioned R380 / MT82 replacement gearboxes for Td5 and Td4. For this item, we charge an additional deposit of 500.00 euros for your current manual gearbox. The deposit will be refunded if you send the old gearbox to us and it is in good enough condition to be overhauled.   If you send us your old gearbox, we will refund you the amount of 500.00 euros. However, this is subject to the condition that the housing is in good condition and the gearbox can still be overhauled. Product note: UB-SCHAGE-TD4 reconditioned MT82 manual gearbox for Defender TD4 (MY2007-2016) UB-SCHAGE-TD5 overhauled manual gearbox R380 for Defender TD5 (MY1998-2006)  

Differentials are among the most important and heavily used mechanical parts and can make a huge difference in performance, especially once you leave the asphalt behind. This much is undisputed, but then the first question usually is whether you need proper lockers on the axles or at least limited slip diffs? Our answer: Unless you’re regularly punishing your Landy in heavy terrain and prefer it climbing over driving, a locker probably makes little sense for you. In ambitious everyday use, retro-fitting a Limited Slip Differential (LSD) like the Ashcroft ATB or the TrueTrac by Eaton will make a huge difference, though. For most drivers most of the time, limited slip diffs will be the best choice on-road, with varying surface and weather conditions, as well as off-road. But first some basics: in contrast to real lockers, which lock up your axle either electronically or pneumatically, LSDs work in the background all the time and not only if you switch them on. Moreover, there is no need for external input. They neutralize the torque differential on one axle gradually or in increments, whereas a real locker has only two states: either completely off or on. This in turn means that the LSD supports the driver continuously and unnoticeably on loose or slippery surfaces and can even beat lockers in certain tricky situations. Every seasoned off-roader will know this one: the vehicle is tilted sideways on slippery ground and the lower rear wheel with most of the load on a locked axle will pull the back of the vehicle violently sideways and downhill when you step on the gas pedal. Moreover, the enormous forces working on locked axles usually require re-enforcements to the drive train, if you want to avoid costly damages in such situations. The Ashcroft ATB LSD, available for Rover front axles (Defender 90/110/130) and rear (90) as well as for the P38 axle on 110/130, is of a Torsen Type 2 design, similar to the Eaton Truetrac, but with a slight difference. The engineers at Ashcroft are employing 6 instead of 3 pairs of helical gears parallel to the axle. The differential creates the necessary friction for torque compensation by pressing these helical gears to the sides of their pockets. Now, if you’re thinking metal on metal, there’s got to be loads of wear on these gears, you need not worry. Both the Ashcroft as well as the Eaton are designed to compensate for the wear and will be among the most long-lived movable parts in the car. One drawback inherent in this particular design is the fact that at least one wheel per axle has to have a load on it for the diff to engage. Pre-load springs on the Ashcroft minimize the effect. If you have both wheels spinning, simply engaging brakes and throttle simultaneously will initialize the torque compensation again. In cars with traction control, this effect is achieved electronically, by the way. The ATB LSD otherwise supports the traction control by multiplying its effects. Because of these characteristics inherent in the design a vehicle fitted with Ashcroft ATBs should never be brake-tested on rollers. The Ascroft ATB is reliable, quiet, supports traction control if fitted, needs little maintenance and improves both the driving characteristics and the power transmission, depending on your setup. It fits Rover and P38 axles (including fittings).  ATB Torsen differential lock Salisbury is only suitable for Salisbury rear axles. For Salisbury axles, the Detroit Truetrac from Eaton is also recommended as an alternative.

Refurbished transfer case LT230 available as:1.2: 1 for Defender TD41: 1.41 for Defender TD51.2: 1 for Defender TD4 with Torsen locking differential1: 1.41 for Defender TD5 with Torsen locking differential1:1.41 für Defender TDI (reinforced version with guide bush)