The protective hoods of roof tents usually have to take a lot during the season. The exposed position of the tents makes this almost inevitable. If the hood is damaged, foxing threatens the tent very quickly. For some, then Gaffa tape is the tried and tested medium of choice. Often enough for the rest of the journey. The consequences of a minimal leaking hood are not immediately visible or smelling! To prevent a nasty surprise in the spring, there is now our repair kit for PVC protective hoods. Material and tools are especially designed for larger repairs. Delivery: 2x brushes 1x 50 ml glue 1x PVC material 48x48cm Manual: Cut the patches and round off the corners. Clean the areas to be bonded (warm soapy water or degreasing detergent) After drying for 10-15 minutes, the glue can be applied to both sides with a brush. (Attention: do not apply too much and above all apply evenly) Let the adhesive surfaces dry again for 10-15 minutes so that the solvents can escape. Touch the glue - if it is dry, you can continue. Place the patches precisely and press firmly. Experts use a roller here. Similar tools like a bottle or rolling pin works too. Important here is the exact positioning, since a later adjustment of the patches is no longer possible. Also, the force that is applied to push the tarpaulin later decides the strength of the adhesive surface. Dry overnight and let air dry for long-term maintenance.

Foam mattress for your roof tent The mattress is available in sizes 140 cm x 240 cm x 6 cm and 165 cm x 240 cm x 6 cm. The delivery takes place WITHOUT mattress cover! Material:The mattress is made of foam with a sub-cover made of 100% cotton. Annotation:The hard version is basically suitable from about 100 kg. Please note that the feeling is subjective and the hard variant may still be too hard for you. Also this mattress is: "Made in Germany" Please select the appropriate width. Please note: For hygienic reasons, this item is generally excluded from return.

Tent Raise +30mm, Mounting Set The Roof Lodge mounting set makes it easy to attach roof tents (folding tents or hard-shell tents) to Frontrunner roof racks. The 30 mm height adjustment bridges the circumferential edge of the roof rack.The mounting set is completely made of stainless steel and is supplied with the necessary mounting material. Please select below whether you require the assembly set for a folding awning (e.g. Roof Lodge) or a hard-shell roof awning (e.g. Maggiolina).Scope of delivery of the assembly set for folding tents:4x raising brackets12x screws, nuts and washers (for fastening the brackets to the support and for connecting the bracket to the sliding plate of the mounting rail).Please note: The sliding plates, which are positioned in the mounting rails of the tent, are not included in the scope of delivery!Scope of delivery mounting set hard-shell tents:6x tent raising brackets12x screws, nuts and washers (for fastening the brackets to the support)6x sliding plates (for positioning in the mounting rails of the tent)6x locker bolts with nuts and washers

Adapter set for mounting the roof tent If the attachment points of the roof tent are directly on the feet of the roof racks, the adapter set offsets the attachment points and the roof tent can be mounted easily and safely. Scope of delivery: 2 pcs adapter plates2 pcs counter platesScrews Note:Sliding blocks and sliding plates are NOT included in the scope of delivery! Are only for better understanding shown in the pictures!The adapter plates are only suitable for beams where the beam foot does not include the crossbar.The carrier feet must NOT be machined in any case!

Finally arrived at the perfect place to make yourself comfortable in the roof tent. And who does not know that: the ladder wobbles because the ground is uneven or even the ladder slips away. This is extremely annoying. The solution is so easy for us.With these leveling feet for roof tent ladders you can adapt to any local conditions. Due to the rubberized surface even a smooth surface is no longer an obstacle. Uneven ground or if you are in the slope, that's no longer a problem. You have a secure grip on asphalt and beyond the paved road. Instructions: Please follow the steps in the pictures (see gallery pictures from step 1 to step 6). Consisting of:2 pieces knurled screw2 pieces of joint feet2 pieces mounting bracket1 piece of storage bag

Mounting kit for Roof Lodge roof tents on Frontrunner roof racks Four longer counter plates, are needed for mounting our old Roof Lodge roof tents on Frontrunner roof racks. The counter plates can also be used for mounting our quick mounting rails on roof racks with wide crossbars! Material: Stainless steel