AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes. All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Comfort is when you don’t have to worry about life’s basics and feeling warm and cozy is definitely one of them, especially when camping, on a weekend trip or a 4x4 adventure. And since there is always too much on everyone’s to do list anyway, it’s a great relief when there’s at least one job you never have to worry about before you hit the sleeping bag or your bunk. That’s where the Comfort Control remote for Autoterm/Planar Diesel air heaters 2D and 4D comes in. Completely redesigned and greatly improved when compared to its predecessor, the Comfort Control activates and deactivates your heater based on timer and/or thermostat settings. Choose from three timer modes for recurring heating intervals, a power mode for constant output, ventilation-only modes e.g. for reducing air humidity inside your camper and last but not least the new thermostat mode. The latter was added due to popular request and allows for setting and maintaining comfortable temperatures by individual degrees centigrade. No more nights in the camper when it’s constantly either too cold or too hot. The new design is also much more comfortable and ergonomic. The OLED display, the multifunctional, non-slip rotary dial as well as two push buttons make selecting and setting the desired functions really easy. Navigating the menus is intuitive and straightforward and basic functions can be accessed directly with a shortcut button. Despite a bigger display and more functions, the  Comfort Control is actually smaller in size than its predecessor. With dimension of only 82 x 37 x 19 mm, you can hide it easily but you don’t have to because the new design is a lot more stylish and will make a nice feature in any camper. Concern for space is one thing in camping mobiles, the usage of electricity is another. In that respect, the remote control has also improved by minimizing its own power consumption. Moreover, the Comfort Control is capable of monitoring the voltage, effectively eliminating the danger of the heater deep discharging the battery. Another great feature is an alert function reminding you when to burn off soot deposits in the combustion chamber. Connecting the Comfort Control remote is as easy as plug & play.

Simple control panel (PU-5) for Planar parking heaters The control panel offers easy operation of the Planar parking heaters. The heater can be switched on or off manually via the control elements. Furthermore, the heat output can be regulated via the control panel.Control elements: Planar-5M  1. switch ventilation off/on2. switch heating on/off3. LED light to indicate the status of the heater    - yellow light = heater running    - slow, red flashing = malfunction4. LED light for status display of ventilation    - Green light = ventilation running    - green flashing = ventilation off    - yellow light = heating and ventilation are on together5. rotary control

AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes. All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Comfort is when you don’t have to worry about life’s basics and feeling warm and cozy is definitely one of them, especially when camping, on a weekend trip or a 4x4 adventure. And since there is always too much on everyone’s to do list anyway, it’s a great relief when there’s at least one job you never have to worry about before you hit the sleeping bag or your bunk. That’s where the Comfort Control remote for Autoterm/Planar Diesel air heaters 2D and 4D comes in. Completely redesigned and greatly improved when compared to its predecessor, the Comfort Control activates and deactivates your heater based on timer and/or thermostat settings. Choose from three timer modes for recurring heating intervals, a power mode for constant output, ventilation-only modes e.g. for reducing air humidity inside your camper and last but not least the new thermostat mode. The latter was added due to popular request and allows for setting and maintaining comfortable temperatures by individual degrees centigrade. No more nights in the camper when it’s constantly either too cold or too hot. The new design is also much more comfortable and ergonomic. The OLED display, the multifunctional, non-slip rotary dial as well as two push buttons make selecting and setting the desired functions really easy. Navigating the menus is intuitive and straightforward and basic functions can be accessed directly with a shortcut button. Despite a bigger display and more functions, the  Comfort Control is actually smaller in size than its predecessor. With dimension of only 82 x 37 x 19 mm, you can hide it easily but you don’t have to because the new design is a lot more stylish and will make a nice feature in any camper. Concern for space is one thing in camping mobiles, the usage of electricity is another. In that respect, the remote control has also improved by minimizing its own power consumption. Moreover, the Comfort Control is capable of monitoring the voltage, effectively eliminating the danger of the heater deep discharging the battery. Another great feature is an alert function reminding you when to burn off soot deposits in the combustion chamber. Connecting the Comfort Control remote is as easy as plug & play.

Simple control panel (PU-5) for Planar parking heaters The control panel offers easy operation of the Planar parking heaters. The heater can be switched on or off manually via the control elements. Furthermore, the heat output can be regulated via the control panel.Control elements: Planar-5M  1. switch ventilation off/on2. switch heating on/off3. LED light to indicate the status of the heater    - yellow light = heater running    - slow, red flashing = malfunction4. LED light for status display of ventilation    - Green light = ventilation running    - green flashing = ventilation off    - yellow light = heating and ventilation are on together5. rotary control

AUTOTERM air 4D (Planar 44D) diesel / air parking heater with additional tank.As a low-priced and powerful alternative to our complete Webasto parking heater kits, we offer the AUTOTERM 4D (formerly Planar 44D) parking heater. The particularly compact dimensions and its heating power of 4 kW allow installation even in small cars, vans off-roaders motor homes, construction machines, boats or under difficult installation situations. The extensive range of accessories supplied simplifies installation. The parking heater has an approval for the European market (ECE mark) and can therefore be installed without registration. The hole pattern here corresponds to the familiar heaters of Eberspächer Airtronic and Webasto AirTop 2000, so that here can be easily replaced without having to drill new holes in the body.All AUTOTERM parking heaters are characterized above all by their durability and reliability with economical consumption. In addition, the heater also has a switchable ventilation function.The parking heater can also be operated while driving. Extensive accessories are available here in our store. The AUTOTERM 4D (prev. 44D) parking heater needs warm air pipes and outlets with 75 mm diameter.Running time: The AUTOTERM parking heater switches off automatically after 2 hours of operation. However, once you press a button during operation, the parking heater will continue to run indefinitely until it is manually turned off.Scope of delivery:- Control element (either simple control PU-5 or Comfort Control depending on your selection.- metering pump- Rubber holder metering pump- Wiring harness metering pump- Wiring harness heater- Intake air hose with integrated silencer- Heat protection hose- End piece exhaust pipe incl. clamp- Tank intake pipe- 5.5 m fuel line- 7 l fuel tank plastic (width: 33 cm + 3 cm intake manifold; height: 26.5 cm + 3 cm bracket + 4.5 cm screw cap, depth: 10 cm)- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- exhaust silencer- screws, nuts, clamps, heat shrink tubing, cable ties- Instruction manualTechnical data:- Fuel type: diesel- Heating power: max. 4 kw, min. 1 kw- Volume of heated air: max. 120 m³/h, min. 70 m³/h- Fuel consumption in operation: max. 0,514 l/h, min. 0,12 l/h- Power consumption in operation: max. 62 W at 12 V operating voltage, max. 58 W at 24 V operating voltage, min. 10 W- Manual start/stop → On the Autoterm.cz site you can find a calculator for correct air heater sizing,You can choose between two control elements:- PU-5 control element with rotary control: the old PU-10 control element had a relatively inaccessible control surface. Therefore, the reliable control element with rotary control is now the new improved standard of Planar parking heaters! With the rotary control you can adjust the heating power of the parking heater and regulate the power of the ventilation in the ventilation mode! The PU-5 control element with rotary control can also be purchased separately here.- The digital control element Comfort Control with timer has an OLED display and an understandable and clear interface.  Temperature, ventilation and power can be configured via the display and the various buttons. With the new timer, you simply set the start of the parking heater to a specific time. The organic light-emitting diodes of the display ensure a particularly high contrast and low power consumption. The digital control element with timer can also be purchased separately here.Setting options (Comfort Control): Temperature and power (adjustable for the parking heater, the control panel and for an external heater) Time and date Operating language (English or Russian) Functions of the timer (Comfort Control): Memory function: save time so that the parking heater starts at this time every day Configurable memory locations: Up to 3 different days of the week with different times can be set and stored. The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater independently reduces the injection quantity according to the ambient air pressure. This reduces or prevents sooting of the combustion chamber when the air oxygen content drops. The maximum heating power decreases proportionally to the amount of oxygen in the air. Roughly one can say: From 2,000 meters the loss of power per 500m altitude is about 5%. Manufacturer tests up to 3.440 m were without problems. Up to 4,000 m, no difficulties are to be expected. Up to 5,000 m the software calculates itself - but this could not be tested in real altitude yet. Please note: Use this 4 kW heater only if this size is really erforgerlich! It is expressly not recommended to permanently turn down the heating. In case of less demand the AUTOTERM Luft 2D (former Planar 2D parking heater) is recommended. If the larger heater is used on a long-term basis on a lower load, the combustion chambers will quickly become sooty - which will cause the heater to fail. https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Planar 2D Auxiliary Vehicle Heater We offer the Planar 2D auxiliary vehicle heater as a well-priced, powerful alternative to our Webasto auxiliary vehicle heater kits. With their compact size and a heater output of 1.8 kW, the Planar 2D is well-suited for fitting to smaller vehicles, vans, off-roaders, camper vans, boats or in confined spaces. It is ideal for 'typical' off-road vehicles like the Land Rover Defender, Mercedes G oder Jeep Wrangler JK. The extensive fitting kit that is supplied with each heater make fitting easy. The Planar 2D can be easily controlled via its analogous control unit, with 8 settings available from 0,8 - 1,8 kW heat output. Available as both, 12 volts or 24 volts, this heater is European market approved (ECE label) and can thus be fitted independet of TUV approval. The parking heater has approval for the European market (ECE test mark) and can therefore be installed without registration. The hole pattern is the same as that of Eberspächer Airtronic and Webasto AirTop 2000 heaters, so that an old unit could easily be replaced without drilling additional holes. All Planar auxiliary vehicle heaters are extremely long-lasting and durable, as well as very frugal. The heater can also be used while driving. And extensive range of additional equipment is available in our online shop. Attention Defender drivers: Our extensive Planar full-set for Land Rover Defender not only includes everything needed to perfectly fit the heater to your Tdi, Td5 or Td4 Defender, but also offers considerable savings over the individual purchase of all included items. Comes with: - 12 V or 24 V heater- Optionally analogue PU-5 control panel with rotary control or digital Comfort Control control panel with timer- Thomas Magnet P327" dosing pump- Exhaust silencer- Dosing pump rubber holder- Dosing pump wiring harness- Heater wiring harness- Intake air hose with integrated silencer- Heat protection hose- Exhaust pipe end piece + clamp- Tank intake pipe- 5.5 m fuel line- 300 mm fuel line connector- 1 m corrugated metal exhaust pipe- Fastening material (screws, nuts, clamps, heat-shrink tubing, cable ties)- Operating instructions Technical details: ·         fuel: diesel·         heat output: max. 1.8 kw, min. 0.8 kw·         air volume: max. 75 m³/h, min. 34 m³/h·         fuel consumption: max. 0.24 l/h, min. 0.1 l/h·         power drain: max. 29 W, min. 10 W·         manual start/stop→ On the Autoterm.cz website you will find a calculator for the correct dimensioning of the air heater The AUTOTERM Luft 2D (Planar 2D) is equipped with a height kit!This means that the heater automatically reduces the injection quantity according to the ambient air pressure. This reduces or prevents shooting of the combustion chamber when the atmospheric oxygen content drops. The max. Heating power drops in proportion to the amount of oxygen in the air. Roughly one can say: From 2.000 meters the loss of power per 500 m height is approx. 5%. Manufacturer tests up to 3.440 m were no problem. No difficulties are to be expected up to 4.000 m. The software itself calculates up to 5.000 m - however, this has not yet been tested in real height. The separately available control unit with timer (optional extra) features a larger OLED display and more intuitive operation. Temperature, ventilation and output can be configured via a display and various switches. An added timer clock allows you to set the heater to a specific time. OLED display provides maximum visibility with minimum power drain.  Possible settings:- temperature and output- time and date- language (English or Russian) Features of the new timer clock:- daily: one fixed time at which the heater starts each day- individual: up to thee different settings with different days and times. The improved new control unit is also available separately.  https://www.autoterm.com/partners/trusted/nakatanenga-4x4-equipment

Comfort is when you don’t have to worry about life’s basics and feeling warm and cozy is definitely one of them, especially when camping, on a weekend trip or a 4x4 adventure. And since there is always too much on everyone’s to do list anyway, it’s a great relief when there’s at least one job you never have to worry about before you hit the sleeping bag or your bunk. That’s where the Comfort Control remote for Autoterm/Planar Diesel air heaters 2D and 4D comes in. Completely redesigned and greatly improved when compared to its predecessor, the Comfort Control activates and deactivates your heater based on timer and/or thermostat settings. Choose from three timer modes for recurring heating intervals, a power mode for constant output, ventilation-only modes e.g. for reducing air humidity inside your camper and last but not least the new thermostat mode. The latter was added due to popular request and allows for setting and maintaining comfortable temperatures by individual degrees centigrade. No more nights in the camper when it’s constantly either too cold or too hot. The new design is also much more comfortable and ergonomic. The OLED display, the multifunctional, non-slip rotary dial as well as two push buttons make selecting and setting the desired functions really easy. Navigating the menus is intuitive and straightforward and basic functions can be accessed directly with a shortcut button. Despite a bigger display and more functions, the  Comfort Control is actually smaller in size than its predecessor. With dimension of only 82 x 37 x 19 mm, you can hide it easily but you don’t have to because the new design is a lot more stylish and will make a nice feature in any camper. Concern for space is one thing in camping mobiles, the usage of electricity is another. In that respect, the remote control has also improved by minimizing its own power consumption. Moreover, the Comfort Control is capable of monitoring the voltage, effectively eliminating the danger of the heater deep discharging the battery. Another great feature is an alert function reminding you when to burn off soot deposits in the combustion chamber. Connecting the Comfort Control remote is as easy as plug & play.

Simple control panel (PU-5) for Planar parking heaters The control panel offers easy operation of the Planar parking heaters. The heater can be switched on or off manually via the control elements. Furthermore, the heat output can be regulated via the control panel.Control elements: Planar-5M  1. switch ventilation off/on2. switch heating on/off3. LED light to indicate the status of the heater    - yellow light = heater running    - slow, red flashing = malfunction4. LED light for status display of ventilation    - Green light = ventilation running    - green flashing = ventilation off    - yellow light = heating and ventilation are on together5. rotary control