Lifting suspension TREKFINDER for SUZUKI Jimny II type GJ from 10/2018 / HJ - the lifting is about 40-50 millimeters. Suitable for model / vehicles:Jimny type GJ from 2018 > / HJdepending on variant: with / without installed cable winch in front depending on variant: with / without steel braided brake line setwith or without LED light with manual transmissionwith automatic transmissionwith 1,5 L engine 75 Kwwith axle loads VA 680 Kg / HA 880 Kgwith ABE-EG number: e6*2007/46*0253*.. oder e6*2007/46*0515*.. SCOPE OF DELIVERY 1-SUJI2F1: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F2: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F3: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F4: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate Translated with www.DeepL.com/Translator (free version)

Wheel spacer for SUZUKI Jimny II Suitable for Jimny II type GJ from model 2018 and type HJ Only the following wheel/tyre combination is listed in the parts certificate: Wheel spacer from TREKFINDER 44 mm for 2 axles:195/80R15 + 205/75 and 215/75R15 Wheel spacer from TREKFINDER 50 mm for 2 axles:195/80R15 + 205/75 and 215/75R15 Wheel spacers from TREKFINDER 56 mm for 2 axles195/80 + 205/75 and 215/75R15 The Trekfinder 56 mm wheel spacer for 2 axles is available with and without mudguard widening. Colour: Trekfinder: silver aluminium

NCC 90 mm LED fog & daytime running lights Daytime running lights and LED fog lights in one headlight! Control unit integrated. ECE and SAE certification. Characteristics: Daytime running light in fiber optic technology LED fog lights With and without metal holder Delivery: In pairs Technical specifications:Dimensions: 90x74 mmLEDs & Type: 3 pcs OSRAM H2L531.TE / OSRAM LUW HWQPVoltage: 12 and 24 VPower at 12 V: Daytime running light: 8.1WFog lights: 8.8 WMounting points: 4 Tapped holes M5Weight: 350 gCertifications: ECE R10, R19, R87, SAEVentilation: DiaphragmMaterial Housing: ADCMaterial of end plate: PC, hardenedTemperature range: -40 ° C - + 80 ° CLead and length: 0.75 mm2 FLRY, l = 200 mmPlug daytime running light: AMP Superseal 282087-1, three-poleFog lights: H8 / H11, two-pole

Spring Spacer Ring/ Trim Packer/ Lifting Ring TREKFINDER for SUZUKI Jimny I & II + 10 Millimeter in colour red - for levelling at the front or/and rear axle. Suitable for all Jimny models at the front and rear axle: Jimny II type GJ & HJ as of MY 2018 Jimny I type FJ until MY 2018 for the front axle spring for the rear axle spring 10 millimetre height adjustment SCOPE OF DELIVERY: 1 piece TREKFINDER polyurethane spring distance ring with marking TREKFINDER logo + FDR10 in colour red. NOTE: The spacer rings are listed in the TÜV® parts certificate for our TREKFINDER Jimny II complete suspension 40 mm and Jimny I suspension 55 mm and can therefore be optionally installed 1x per spring.A general TÜV® parts certificate is not available or is NOT included in the scope of delivery. MOUNTING INSTRUCTIONS: The installation is carried out between the upper end of the spring and the spring plate. Make sure that the brake line is long enough Make sure that the shock absorber is long enough. Check the headlight setting. The permissible height of the coupling ball must be observed. If there is a load-dependent headlight adjustment, e.g. for LED lights, this must be checked and, if necessary, adjusted or changed/extended. If a new measurement or calibration of the sensors of the driver assistance system is necessary due to the changed vehicle geometry of the vehicle, this must be carried out according to the specifications of the vehicle manufacturer. For vehicles with load-dependent brake pressure regulator, this must be readjusted to the empty level (according to the vehicle manufacturer's specifications). After retrofitting, the axle geometry of the vehicle must be measured and, if necessary, corrected according to the vehicle manufacturer's specifications.

Alloy wheel for Suzuki Jimny 2 GJ/HJ High Peak J-01, 6x16 The High Peak J-01 light alloy rim is available in a clear retro style in three different colours.The robust rim is perfect for modern off-road vehicles.Specially designed for the Suzuki Jimny GJ/HJ, TÜV approved and strength tested.Also compatible with JB43 (1998-2018) models.Bolts on with standard or higher suspension. No additional modifications required (depending on tyre size).With TÜV parts certificate for Suzuki Jimny GJ (the parts certificate for HJ will follow shortly).   Diameter : 16Width : 6OFFSET : -5Bore / PCD : 5x139.7Finish : black matt, anthracite matt or vintage whiteWeight : 9.2kgVehicle : Suzuki Jimny 2 GJ/HJIf you need a complete wheel set, please contact us by e-mail or phone.info@nakatanenga.deTel. : +49 9181 466 644

Rear ladder for Suzuki Jimny 2 type GJ BJ 2018 / HJ Boxier, tougher and even more capable, that’s the Suzuki Jimny 2 (GJ/HJ MY 2019). Even if cargo space has grown considerably in comparison with the previous model, optimizing your usable load capacity is still crucial if you want to get the most out of this little giant. Considering the limited interior that means first and foremost to use the roof space to the full extent: either with our own dedicated CargoBear system for the Jimny or any other conventional roof rails, bars or racks. Whatever solution you prefer, our light and strong aluminum ladder makes accessing the roof area a lot easier. Climbing to the rooftop is safer, more comfortable and allows for stress-free loading, fastening or strapping down of your cargo. The ladder is mounted on the tailgate only and has no connection with the roof or the rack, making it ideal for all kinds of carrier systems. Additionally, there is no need to drill holes either as the ladder is custom-designed to fit existing mounting points and screw holes: on the spare wheel mount, the tailgate’s drip rail and the bottom right door hinge. This also allows for quick and easy de-installation without damage or marks. The ladder is made from high-quality aluminum and features black powder coating – a perfect match for our modular CargoBear roof rack system.