Tank-mounted fuel intake pipe The 60 cm tank-mounted fuel intake pipe is perfect for our diesel heaters by Autoterm, but will also suit most other products like Webasto or Eberspächer. It will work with both diesel and gasoline on either air or water heated systems and it doesn’t matter whether your tank is plastic or metal. To fit the intake pipe, it is generally necessary to remove the fuel tank and its fittings. After drilling a hole for the intake pipe, the connector head has to be countered with a nut from the inside. That’s why access to the tank’s interior through the intake opening is a must. The flexible riser pipe can be bent into any shape, making it easy to determine the extraction level for the heater. Make sure that the opening of the pipe doesn’t reach all the way to the bottom of the tank, otherwise you’ll risk complete emptying of your fuel tank and the unwanted intake of dirt particles or tank sludge. The tank extraction is ideally suited for our Planar parking heaters.

Nakatanenga Double Socket USB and USB C Socket incl. Spacer USB socket type A and C, round, suitable for 12V and 24VInput: DC 12V-24V,Output: Type A (QC3.0 port): 3.6-12V / max. 36WOutput: Type C (QC4.0 port): 5V-20V / max. 60WWith the output type C can also charge laptops of any kind (slow charging)Hole diameter hole: 29mmPlease note the installation depth if you want to install the USB socket e.g. in a parking heater console or a valuables compartment. As the USB socket is slightly longer than a normal 12 volt socket due to the Quickcharge, please use the spacer supplied. Socket has an ON/OFF switch and PD technology.

Spare parts kit for mobile parking heaters. To ensure that your parking heater remains watertight, you will receive the common wear parts here. Set consists of: 3x rubber plugs 2x O-rings 2x thread caps 1x storage bag

Who doesn't know them, the not really cheap 12 V extension cables and adapters from the DIY store? Usually quickly packed just before a trip, disillusionment soon sets in when devices do not work/charge properly due to wobbly plugs, fuses permanently blow because the cables are too thin or there is a short circuit due to moisture penetration. The length of the list of product features shows how much effort and thought has gone into the two cables offered (with one or two sockets): rubber seal on the plug to prevent dust and moisture penetration control LED and 10 A fuse integrated in the plug integrated strain relief to protect the cable waterproof cap on the socket locking system for secure fit (requires corresponding socket) Integrated strain relief to protect the cable all contacts nickel-plated for low contact resistance mountable and dismountable (with suitable adapters) available with one or two sockets

12 V plug, suitable for common cigarette lighters and 12 V sockets, can be loaded up to 10 A, interlocks with the matching socket NABS1011. Product features: Waterproof sealing ring on the shaft to prevent moisture from entering the socket. Status LED Integrated strain relief 10 A fuse built in designed to withstand heavy moisture and vibration "Twist-lock" system for secure locking with the NABS1011 socket outlet Seal at cable outlet (4mm diameter) Max. Voltage: 15 V Max. Current: 10 A Scope of delivery: 1 plug

12 V socket with rectangualar mounting plate and waterproof cover. Up to 15 A current, locks with the suitable plug NABS1010. 12 V socket, waterproof, 15 A Product features: waterproof cover to prevent water ingress included strain relief for severe humidity and vibratios can be mounted with or without supplied mounting plate large contact area for best power transmission "Twist-Lock" system for secure locking with NABS1010 plug cable-side seal (4 mm diameter) max. voltage: 15 V max. current: 15 A included in delivery: 1 socket

fits all Defender from MY99 up to and including Td4

A-pillar lamp holder Jeep Cherokee & Comanche The brackets allow the mounting of lights on the A-pillar of the Jeep Cherokee XJ and Jeep Comanche MJ, supplied in pairs, incl. blind rivet nuts. Ideal for this mounting location are compact LED lights with tightly focused illumination (thus minimizing reflections from the bonnet), we recommend the Vision-X Cannon LED driving lights here. The brackets are made of stainless steel and can also be supplied with a black powder coating - please select the desired variant below.

Accessories Dashboard Mounting Point for New Defender L663 Practical mounts for cell phones, navigation devices, tablets, and other gadgets are indispensable, because even the latest cars with all their "connectivity" don't deliver everything an off-roader, overland explorer or ambitious camper requires. However, cheap plastic mounts are usually a waste of money and not everyone wants to stick suction cups to their windows either. Our mounting plates for the side handles on the dashboard of the New Defender are designed to support heavy duty mounts – like those from market leader RAM Mounts. The plate’s tight hold makes sure that nothing wobbles, collapses or falls off. But most of all, there are no suction cups involved as they tend to come loose when off-roading or speeding along bumpy dirt roads.The mounting plate is powder-coated black to match the interior of the new Landy and you simply fasten it with the existing screws of the handle. No drilling is required and removal is as easy as installation. Three strong, internally threaded 6 mm screw holes (M6) allow you to mount ball joints, brackets and other mounting equipment, either from RAM Mounts or other brands. In our bundle solution, the mounting plate comes with a 1-inch ball (type B) from RAM Mounts. Available with or without RAM Mount ball.  

Accessories for OptiMATE solar battery charging systems Product Informations Extension cable with a length of 4.6 m with SAE connection Length = 15 ft / 460 cm 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -20 ° C / -4 ° F Use at very low temperatures SAE built-in socket Length = 100 cm / 40 " Front mounting, rear mounting, for sheets from 1 mm / 0.040 "thickness 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -40 ° C / -40 ° F Use at very low temperatures; stays flexible at temperatures below freezing SAE built-in socket (short cable) Length = 15 cm / 6 " Front mounting, rear mounting, for sheets from 1 mm / 0.040 "thickness 2-pole industry-standard SAE connector Max. Cable values: 5 Amp -40 ° C / -40 ° F Use at very low temperatures; stays flexible at temperatures below freezing Plug with rotary adapter, fits on Ø 12 mm MOTORCYCLE / DIN or Ø 21 mm AUTO sockets, with 2-pin SAE connection according to industry standard Length = 20 ″ / 50 cm Industry standard 2-pin SAE connector 8 A fuse (in the plug) Max. Cable values: 5 Amp -20 ° C / -4 ° F Use at very low temperatures With rubber cable gasket for OptiMate heavy-duty SAE connection. Y splitter, SAE IN to 2 x SAE OUTBranching your permanent battery supply line, creation of SAE outputs. Length = 12 ″ / 30 cm Industry standard 2-pin SAE connector. Max. Cable values: 5 Amp -20 ° C / -4 ° F use at very low temperatures With line seals and sealing end caps for OptiMATE heavy-duty SAE connections. https://www.youtube.com/user/TecMate1/about

Adapter / Reducer 90-60 and 75-60 Warm Air Pipe for Parking Heaters With this adapter or reducer you can reduce the warm air duct of a parking heater from a 90 mm warm air pipe to a 60 mm warm air pipe.The 75-60 adapter is intended, for example, to connect a 75mm warm air pipe with a 60mm connection piece.

Adapter for connecting 2 Alan PL259/6 plugs.

End piece for warm air hose WALUFLEX Our 60 mm Flexi pipes for parking heaters are the perfect solution for transporting warmth and cosiness from A to B, whereby B can be one of our roof tents, a cold mountain hut or whatever else needs to be heated off-grid. The warm air pipes can be cut to any length and to ensure that the pipe ends are cleanly sealed or can be easily and airtightly extended, we have a silicone adapter for easy ratcheting. The adapter is the icing on the cake for our hot air ducts. It might work without, but it's definitely better with. For one thing, it is safer for people, equipment or cars because the edges, fringes and wire ends of the cut pipe disappear under the silicone cover and therefore have no chance of scratching, pricking or tearing. It is also very practical: one end of the silicone adapter is semi-permanently attached to the cut-off pipe with one of the cable ties supplied. The other end of the adapter can then be tightened to a connection or extension as required using the ratchet clamp (ideal for our parking heaters). Without the ratchet, the silicone adapter, which only makes the pipe 5 mm thicker, is a perfect and aesthetically pleasing end sleeve. After all, the eye camps with you and who wants to look at fraying pipe ends.    

Additional tank 7.5 litres for parking heaters This additional tank can be placed anywhere on the vehicle.The tank can be filled with 7.5 litres of fuel, e.g. for the AUTOTERM Planar 2D parking heater. Suitable fastening material is included in the scope of delivery.

Adjustment adapter for electric speedometer / odometer When fitting new tyre sizes, modern vehicles with a factory-integrated speedometer usually have a speedometer discrepancy, as this is often not configurable. In the long run, the incorrect speed indication is annoying and sometimes results in an incorrect total kilometre reading (the odometer goes wrong) and consequently even in a poorer resale value of the vehicle. The speedometer adjustment with the adjustment adapter is an inexpensive solution to avoid this problem.Technical data:Power supply: 9 - 28 voltsQuiescent current consumption: 4.6 mA at 13.8 volts power supplyInput signal: min. 2 volt peak, potential-independent, max. 4.5 kHz at 12 volt input signal or max. 1.6 kHz at 5 volt input signalOutput voltage: square-wave signal equal to the operating voltage minus 1.3 volts, maximum 13.1 volts, maximum 5 kHzSecond output stage with sine wave signal

Adjustment adapter SpeedoHealer  When fitting new tire sizes, modern vehicles with a factory-integrated speedometer usually have a speedometer discrepancy, as this is often not configurable. In the long run, the incorrect speed indication is annoying and sometimes causes an incorrect total mileage (the odometer goes wrong) and consequently even a poorer resale value of the vehicle. The SpeedoHealer speedometer alignment is an inexpensive solution to avoid this problem. Suitable for TD5 vehicles from MY1998 to 2007 The alignment adapter is simply connected to the green speedometer sensor located on the transfer case of the Defender. The SpeedoHealer then detects the correct speed from the output pulse of the speedometer sensor. Functions of the SpeedoHealer: Speedometer adjustment or elimination of inaccuracy of the original speedometer.Conversion of kilometers to miles or miles to kilometers (useful for a vacation abroad or for imported vehicles)Accurate indication of the maximum speed driven at the push of a buttonNeutralization of the speed limiter on some vehicles

Radio 90 CB antenna for fixed mounting Technical data:  Length approx. 90 cm 200 W 4 m cable with DV plug 1/4 lambda The antenna has an open-ended cable to make it easier to lay the cable. A PL259/6 plug for RG58 coaxial cable is required for connection to a radio.

Magnetic base antenna for CB radio, approx. 145 cm long. Technical data: Type: 5/8 LambdaPower rating: 200 WLength of steel: 148 cmRadiator material: stainless steelMagnetic base: 120 mm diameterThe antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

Alan PL259/6 plug, for RG58 coaxial cable PL259/6 plug, double pack, for assembling RG58 antenna cables.Required for the Alan ML130 and Alan ML145 magnetic antenna.

The 1/4 lambda antenna is easy to mount and offers a wide bandwidth incl. DV connection. It consists of a stainless steel radiator with flux points and a wing nut. The standing wave ratio is preset and can be changed by changing the radiator length. Mounting instructions: Drill a hole with a diameter of 12 mm at a point on the vehicle body.Deburr the hole and ensure a good conductive connection of the antenna flux.Then insert the antenna base from the outside of the body into the hole so that the corrugated side of the antenna joint faces the outside of the vehicle. Fit the plastic washer and the metal trident washer the right way round. Fit the toothed washer and screw on the nut loosely After aligning the base, tighten the nut on the inside of the body with a spanner Screw on the angle plug with the antenna cable (tip: seal with silicone to permanently seal the mounting point against rust) Mount the radiator with the threaded bolt on the antenna base Technical data: Frequency: MHz 26-28 Type: 1/4 Lambda Power rating: 300 W Radiator length: 130 cm Steel material: Stainless steel SWR Adjustable - SWR adjustment via length change: SWR preset Special features: Plug type DV Total length with base: 138 cm The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio set you still need a PL259/6 plug for RG58 coaxial cable.

The ALBRECHT AE 6110 has all the essential functions that you need. The highlight: With a width of only 10 cm and a height of 2.5 cm, it can easily be accommodated even in the smallest of spaces. With its die-cast housing, it is very stable. New: with integrated VOX function for hands-free speaking in the vehicle Properties: All European CB standards S-meter, 6-level LED indicators for RX and TX VOX hands-free function Receiving sensitivity adjustable (RF gain) Channel 9/19 direct selection button (EMG) Die cast housing 4 watt AM / FM Automatic squelch (ASQ), adjustable in 9 levels Further equipment features: Channel selection buttons on the microphone Channel search (scan) Keylock Socket for external speaker Technical specifications:Dimensions: 102 x 100 x 25 mm³Weight: 450 gSupply voltage: 13.2 V.Power consumption: 2 A max.Operating temperature range: -20 to +50 ° CAntenna input: UHF, SO-239Frequency error: <+/- 300 HzTransmission power: 4 wattsInterference transmissions: <4 nW (-54 dBm)Adjacent channel power: <20 µWFM frequency deviation: <1.9 kHzAM modulation depth: <90%Reception sensitivity: better than 1 μV (20 dB SINAD)Mirror selection: 70 dBAdjacent channel suppression: 60 dBAudio output: 1 watt into 8 ohmsFrequency response: 300-3000 Hz Conversion option for licensed amateur radio operators:10 m amateur radio band, 400 channel mode: 25,610-30,105 MHz, 8 watts Scope of delivery: AE 6110 CB radio, microphone with up / down buttons, microphone holder, mounting bracket with screws, instructions

This CB mobile antenna scores with good SWR values - the fine-tuning of the SWR values is done by rings. Technical data: CB mobile antenna 1/4 lambda 120 channels Power rating: 40 watts Material: Stainless steel SWR Adjustable YES Length: 115 cm Cable length: 4 metres For fixed mounting The antenna has a cable with an open end to make it easier to lay the cable. For connection to a radio, you still need a PL259/6 plug for RG58 coaxial cable.

18350 Li-Ion 900 mAh battery This is Armytek’s official battery for the Tiara A1 Pro, a Li-Ion rechargeable with 900 mAh. As always with Armytek, the battery is designed to meet the highest requirements, especially in the flashlight’s turbo modes. It can be charged up to 500 times and is protected by a thermal cut-off vent. We recommend using the Uni C4 charger with your rechargeable batteries. - Can be recharged over 500 times, equivalent to 500 single-use CR123 batteries- «+» flat contact- Safety ventilation slots for protection against overheating- Battery output voltage: 3.7 V- Capacity: 900 mAh

Product description Uni C4 Plug Type C Universalladegerät If you are familiar with the Armytek flashlights Tiara, Wizard and Prime, you know that the Canadians are always trying to get the most out of different battery types for maximum performance. The technology concerning battery and charge management is second to none whether it’s battery recognition, charge level monitoring, temperature control or the prevention of current drain when the lamp is switched off. No wonder Armytek is packing everything that’s intelligent and user-friendly into their universal charger Uni C4 with its Type C plug and car adapter. The four charging slots support any combination of Li-Ion, Ni-MH, Ni-Cd, LiFePO4 and Ni-Zn batteries and automatically provide the optimal current of up to 2 A for every battery type and charge level. Even fully drained batteries are recognized and recharged with gentle 0.1 A. Among the Uni C4’s safety features are the detection of bad rechargeables, disposable batteries or reverse polarity. Multi-colored LED’s with an extra night mode indicate charging status and levels and, as always with Armytek, a reassuring 5 years no-hassle warranty proves their confidence in the product’s quality. Supports IMR/Li-Ion, Ni-MH, Ni-Cd, LiFePO4 and Ni-Zn batteries Quick charge with up to 2 A current Easy selection of battery type and charge current with one button per each channel Multicolor LED indication with Night mode and useful 5 LEDs per channel Over-discharged and sleeping battery activation function with safe 0.1 A current Saving of actual battery type to restore after electricity interruption Auto-detection of bad batteries, reverse polarity and primary batteries Capability of hand settings for safe current and type of battery, which is found as bad 5 years no hassle warranty Technical specifications: Plug type: Plug type C Technical details of chargers Number of channels: 4 Battery type: IMR/Li-Ion, Ni-MH, Ni-Cd, LiFePO4, Ni-Zn Battery compatibility: diameter 8..32 mm and length 30..70 mm (10440, 14500, 16340, 18350, 18650, 26650, 32650, AAAA, AAA, AA, C, D) Voltage per channel: 4.2 V / 3.65 V / 1.9 V / 1.5 V Charging current per one channel: 2 A / 1 A / 0.5 A / 0.1 A Input: AC 85-264 V / 0.5 A (50/60 Hz) or DC 9-14 V / 1 A Indication type: 4х5 multicolor LEDs Weight: 271 g What's included: Car adapter, power cord, manual