Wing flares TREKFINDER universal - 4 PIECES - 23 millimetres wide and 150 cm long - incl. TÜV® report inexpensive and flexible mudguard extensions in very good quality indestructible and therefore durable mudguard extensions made of black rubber ideal e.g. for track widening with wheels, spacer discs etc. - for prescribed registrations or off-road use the fender flares are glued in the wheel arch under the web edge of the bodywork the factory backing film is removed and the widening can be securely bonded to the clean surface/web edge for difficult off-road applications, additional fixing of the widening with screws is recommended the widener is 39 millimetres wide in total - of which approx. 16 millimetres are used for mounting and approx. 23 millimetres then protrude outwards to cover the tyres SCOPE OF DELIVERY: 4 TREKFINDER mudguard extensions, each 150 cm long, 1 TÜV® test report 1 type plate 1 piece fitting instructions 1 photo sheet ATTENTION - important installation instructions: the mounting surface must be smooth, rust-free, thoroughly cleaned and free of grease the outside temperature and the temperature of the components or mounting surface at the time of installation and for a period of 24 hours thereafter must be at least 20° Celsius after removing the 3M tape carrier film, the widener must be pressed evenly against the mounting surface for approx. 1 minute with high pressure adjust the ends of the widening to your taste with a sharp carpet knife to match the look of the vehicle Please allow the vehicle to stand for at least 24 hours after installation, preferably 48 hours the final strength of the bonding is only achieved after 48 hours Please do not wash the vehicle for at least 48 hours in some installation situations, especially if the installation instructions cannot be adhered to, additional fastening with e.g. self-tapping screws, body adhesive, primer is recommended

Mudguard widening kit for the Suzuki Jimny I FJ from TREKFINDER - 4 pieces, each 150 cm long / tyre tread cover 20 mm / incl. TÜV® / universal mounting Ideal e.g. with the 56 mm wheel spacer from TREKFINDER in combination with 215 tyres on 5.5J standard rims !!! Inexpensive and flexible wing flares in very good quality indestructible and therefore durable mudguard extensions made of black rubber the fender flares are glued to the existing wing flares of the Jimny and additionally fixed with screws (the screws are not included in the scope of delivery) the factory backing film is removed and the fender flares are then glued to the clean surface SCOPE OF DELIVERY: 4 TREKFINDER mudguard extensions, 150 cm each 1 TÜV® test report 1 type plate 1 piece assembly instructions 1 photo sheet ATTENTION - important installation instructions: the mounting surface must be smooth, rust-free, thoroughly cleaned and free of grease the outside temperature and the temperature of the components or mounting surface at the time of installation and for a period of 24 hours thereafter must be at least 20° Celsius after removing the 3M tape carrier film, the widener must be pressed evenly against the mounting surface for approx. 1 minute with high pressure adjust the ends of the widening to your taste with a sharp carpet knife to match the look of the vehicle Please allow the vehicle to stand for at least 24 hours after installation, preferably 48 hours the final strength of the bonding is only achieved after 48 hours Please do not wash the vehicle for at least 48 hours in some installation situations, especially if the installation instructions cannot be adhered to, additional fastening with e.g. self-tapping screws, body adhesive, primer is recommended  

ender flares TREKFINDER universal - 1 PIECE - 35 millimeters wide and 150 cm long - incl. TÜV® report inexpensive and flexible fender flares in very good quality indestructible and therefore durable fender flares made of black rubber ideal e.g. for track widening with wheels, spacers etc. - for prescribed registrations or off-road use the fender flares are glued in the wheel arch under the web edge of the bodywork the factory backing film is removed and the widening can be securely bonded to the clean surface/web edge for difficult off-road applications, additional fixing of the widening with screws is recommended the widening is 51 millimeters wide in total - of which approx. 16 millimeters are used for mounting and approx. 35 millimeters then protrude outwards to cover the tires SCOPE OF DELIVERY: 1 TREKFINDER mudguard extension 150 cm, including screws 1 TÜV® test report 1 type plate 1 piece fitting instructions 1 photo sheet ATTENTION - important installation instructions: the mounting surface must be smooth, rust-free, thoroughly cleaned and free of grease the outside temperature and the temperature of the components or mounting surface at the time of installation and for 24 hours afterwards must be at least 20° Celsius the widener must be pressed evenly against the mounting surface with high pressure for approx. 1 minute after removing the 3M tape carrier film adjust the ends of the widening to your taste with a sharp carpet knife to match the look of the vehicle please allow the vehicle to stand for at least 24 hours after installation, preferably 48 hours the final strength of the bonding is only achieved after 48 hours Please do not wash the vehicle for at least 48 hours in some installation situations, especially if the installation instructions cannot be followed, additional fastening with e.g. self-tapping screws, body adhesive, primer is recommended (fixing screws are included in the scope of delivery) The extensions are suitable for almost all vehicle types and vehicle models of all vehicle manufacturers, such as:Ineos Grenadier, Jeep, Land Rover, Ford, Nissan, Suzuki, Toyota and many others (cars, vans, off-roaders, construction machines, trailers, agricultural machinery, etc.).  

Fender extensions universal This broadening in discreet optics is suitable for vehicles with and without inner edge in the wheel arch. Ideal for widening spacers, wider tires, rims with greater press-in depth, etc. Available in different widths: 18 mm, 23 mm, 28 mm - please select the desired widthLength: 150 cm Suitable for: car, SUV, VAN, trailer, camper, construction machine, agricultural machine, etc. Attention - installation instructions: The adhesive tape that we use for this profile is the best that we have: Article 3M 4222If the extension fender will be applied on a normal situation, we don not need to use Primer.The important is to follow the correct fitting instruction: 1)      Perfect cleaning of the surface that will receive the adhesive tape2)      Position the profile and apply using a strong pressure for all the length of the adhesive tape3)      Correct temperature for the application: minimum + 20°C4)      To be sure that the adhesive tape is working correctly, you can apply a masking tape, to keep the pressure for the next 24 hours5)      Do not wash the car for 48 hours after the application

Extended wheelarches for Land Rover Defender Often the fender flares are too narrow for the Defender. With this widening you get a wheel cover of + 30 mm. This extended wheelarches for Defender is made of a very flexible material, which allows easy and quick attachment to the wheel arch. The 30 mm widening & increase is also great for wider tires. Even a trackless dismantling is possible without further ado. suitable for Land Rover Defender until MY2016 incl. plastic expanding rivets NOTE: You will need a piece (white, dashed mark) of your old widening (picture 1) on the front axle to attach this fender widening. You can see a detailed marking for the cutting on picture 2 and picture 3. On picture 4 you will find the final result as well as the position at which point a further manual drilling is necessary. Finished!

Whether you’re going for a more muscular look or just better off-road performance, there are many good reasons to widen your Defender’s stance. You can go for fat MT tires or you can widen the track with wheel spacers or negative offset rims to achieve the desired effect. But keep in mind that your wheel covers may no longer be sufficient for your country’s road regulations and that in turn could affect your 4x4’s road legality. Apart from costly surprises in traffic stops, you also want to avoid potentially dangerous water and mud spray or debris being catapulted from exposed wheels. And then there’s also that slightly unbalanced look… At Nakatanenga, we thought there’s got to be a better solution than what’s out there and that’s why we teamed up with the experts at TREKFINDER to give you a functional, easily attached and exclusive solution to extend your existing original wheel arch guards. The result is a discrete self-adhesive rubber extension strip that widens the original Land Rover wheel arch guard by another 20 mm, simply by sticking it onto the original part. There’s no need to remove the original parts, drill new screw holes etc. The new guard’s protruding adhesive lip fits perfectly onto the original part and makes it very easy to position the 1.5 m extension perfectly. This should also work with identical after-market parts by Britpart et al, but with non-original parts we are unable to provide a warranty, of course. With a little experience and some planning, though, you can easily adjust the strips’ required length or their radius with a boxcutter and some sanding paper. Again, alterations are not covered by our product warranties. And last but not least, since our wheel arch extensions are self-adhesive, they are just as easily removed as they are mounted. Our Defender wheel arch extensions by Nakatanenga and TREKFINDER are available in a set of four with identical front and rear attachments and are exclusively available in our shop. Material:Black rubber, very good quality - flexible and almost indestructible Complete vehicle kit:4 pieces of 1,500 mm length each

Mudguard widening universal - 2 Pcs - 60 millimetres wide and a 150 centimetres long. An inexpensive, flexible and beautiful solution. The wing extension is made of robust hard rubber. The specified width of 60 mm is measured when mounted from the outer edge of the body. This means that the wing extension is 90 mm wide in total, 30 mm of which are available for mounting on the wheel arch, the remaining 60 mm are for covering the tyre. The fender extension is mounted from "below", i.e. for mounting on the vehicle there should be a minimum of 1 cm wide web edge (= wheel arch edge parallel to the tread of the tyre) in the wheel arch. The widening is screwed from below to the web edge with the fastening screws included in the scope of delivery. Scope of delivery: 2 pcs. wing extensions a 150 cm longFixing screws