Great conversion kit for the 2nd row of seats With the introduction of Td4 Puma models from MY2007 onwards, Defenders featured not only a new engine and drive train but also significant changes to the interior. Due to new safety regulations, second row seats and their mounting points required a new layout. Consequently, more recent Td4 back seats will not fit when restoring or converting older pre-2007 models.  Our conversion kit enables you to install post-2007 second row seats in pre-2007 110 Defender Station Wagons. The back seat mounting kit contains a mid-crossmember, two second row seat supports, chassis bracket fixing kits and two adapted front panels for the rear wheel arches. All parts are galvanized.

Corner protector for Defender seat box The edge of the Defender seat box is susceptible to damage and sometimes looks quite pitted and unsightly after a while. With these elegant corner protectors, you can spruce up the seat box and protect it at the same time!Made of 3 mm black metal and CNC-milled to the highest precision. With the help of a cordless screwdriver and the included fastener, the corner protectors are attached in less than 5 minutes! The kit contains a pair of corner protectors and 12 pcs. 8x19 mm steel screws. The corner protectors also fit a Series 2 and 3, but require a matching hole to allow the seat rail to be attached.Scope of delivery: One pair of corner protectors incl. fixing material. Illustrations may differ.

Everyone knows the bits and pieces lying around in the car that are not needed all the time, but still have to be close at hand. But where do you put it? The HIDDEN BAG storage compartment for the original seats of the Land Rover Defender is easily attached via four high-tensile Velcro and fleece surfaces under the driver or front passenger seat. The bag offers storage space for the 1000 little things of everyday life such as pens, screwdrivers, pliers, multitool, flashlight, batteries for a remote control, USB stick with workshop manual, spare glasses, air pressure tester, charging cable and much more. But even a small digicam, a GPS device or other valuables are quickly out of sight and accessible. The traveler may stow a second passport, unauthorized radio or copies of their travel documents. The scope of delivery includes 4 self-adhesive and tensile Velcro strips for the seat side. The bag is attached to these Velcro strips via its 4 fleece surfaces (see pictures below). The storage bag fits perfectly under the Defender seat and, thanks to Velcro surfaces, can be easily removed and transported using the attached carrying strap. The high-quality fabric made of polyamide 6.6 ensures that the bag remains breathable and moisture and dirt are still strongly repelled. The bag has a small mesh compartment on the upper inside and a detachable intermediate compartment on the lower inside. The stowage bag was manufactured according to US military standards (MIL-SPEC) and our specifications by Delta Bags in Germany. Dimensions: 18x33x8 cmWeight: 260 g Fastening via four tensile Velcro and fleece surfaces each (included in delivery):

Retrofittable seat heating Deluxe 12V The high-quality carbon seat heating system was developed for retrofitting in individual seats.You can switch off the heat supply of the carbon surface heating elements via a switch (0% power) or set it to one of 3 different heating modes: Mode 1: 25% power Mode 2: 50% power Mode 3: 75% power This three-stage system provides pleasant warmth within a few minutes. When a level is set, the heater heats up to 100% power in just two minutes and then adjusts down to the desired mode (25%, 50% or 75%). This allows the carbon panel heating elements to reach the desired heat output much more quickly. The button or switch indicates the current level via three LEDs integrated into the button. The button can easily be stuck horizontally or vertically anywhere. Three adjustable levels and remarkably fast temperature regulation make this seat heater unique. Differences between carbon panel heating elements and heating elements using stranded wire technology: The carbon panel heating elements have considerable advantages over the previously widely used heating elements with stranded wire technology. For example, only carbon heating elements can be adapted and trimmed during installation. With conventional stranded wire technology, a heating wire runs inside the heating element in the form of a wave. If this is damaged at any point, e.g. due to mechanical stress or overheating, the entire heating element fails. Parallel technology is used in the new carbon surface heating elements. Many independent carbon heating fibers run inside the heating element, ensuring its reliability. The heat distribution is much more homogeneous and therefore more pleasant with carbon panel heating elements. Scope of delivery: 2 carbon heating mats (one for the seat and one for the back) 1 wiring harness 1 button incl. necessary installation material and installation instructions   Technical data: Size of the heating mats: 645 x 250 mm (can be trimmed according to the installation instructions) Operating voltage: 9.6 V - 15 V Operating temperature range: -20 °C to +80 °C Power: up to 90W@13.8V Certification: ECE, EMC  

Seat pad Land Rover Defender Many Landy critics bemoan the seat position in the Defender, the missing elbow room and the spartan original Land Rover seats. But that’s doing a disservice to the furniture from Solihull, especially the improved versions that were introduced in 2007. Even taller drivers, with seat rail extensions installed, can do mile after mile without problems for back and behind. So, if you’re restoring an old Defender or you put too much mileage on yours, it’s worth considering to refurbish the old seats instead of putting brand new ones in. As long as the seat covers are fine and only the foam cores have disintegrated, an upgrade with new seat foams can make a huge difference. This is classic DIY and pretty easy to do with our replacement foams for backrests and seat cushions. Simply remove the whole seat, take the backrest and seat cushion out, remove the covers and rip the old foam off the frame. The new foam cores can be fixed to the frame with standard spray adhesives. Then reverse the process and enjoy your firm new seats. The seat fits all Defender standard outer front seats up to 2016, the backrest for 2007 - 2016. Not suitable for special models.

Trekfinder cover profile for airline rails Available in: 1 m or in 10 cm increments (free choice of length) - max. 25m in one piece. Please note:As there are so many different applications and we do not know your requirements, we need you to provide us with the info on which length and which denomination of profiles you need.Please enter your cutting requirements in the free field at the end of the order process. Individual cuts are excluded from exchange. Airline rails would have to be invented if they didn't already exist. Few lashing systems are as flexible, stable and secure at the same time. Anyone who has ever had to lash large, uneven and sometimes delicate objects in the hold or on the roof knows what we are talking about. So how do you make airline rails even better? With rubber profiles from Trekfinder, which are clicked into the rails. It's easy, quick and holds firmly and securely. With their 3.5 mm height, the rubber profiles are hardly noticeable and first and foremost prevent dirt and dust from penetrating into unused rails or rail sections. This is particularly important on loading areas or trailers, because dirty rails make it much more difficult to attach fittings and lashing points. Of course, the same applies to snow and ice in winter and who always wants to scrape the airline rails free? On top of that, the covers ensure better load securing when the load is placed directly on them. In the case of roof racks, they also reduce wind noise, and when the rails are attached to the side, nothing gets caught by vegetation off-road. A lot of performance for little money. The cover profiles are available in 30 mm width. Note: DOES NOT FIT THE V-Class/Vito/Viano

TREKFINDER cover profile for Mercedes V-Class/Vito/Viano - for factory fitted floor rails - textured surface. Available in: 1 m or in 10 cm steps (free choice of length) - max. 25m in one piece Please note:As there are so many different possible applications and we do not know your requirements, we need you to provide us with the info on which length and which denomination of profiles you need.Please enter your cutting requirements in the free field at the end of the ordering process. Individual cuts are excluded from exchange. made of high-quality, flexible and black rubber - does NOT fit on classic airline rails!!! especially and exclusively for Mercedes models: V-Class, Vito, Viano perfect adhesion due to U-construction on the underside easy mounting by clipping into the floor rail the possible max. length as one piece is 25 m flexible, high-quality black rubber anti-slip surface with wave structure Note: the return of any remaining quantities is NOT possible!!!!