The additional spring kit for the rear axle of the Land Rover Defender 110 and 130 increases the spring rate and thus minimises the effects of high payloads. The kit consists of 2 additional springs, 2 upper brackets and 2 lower brackets. This kit is intended for vehicles that are permanently or predominantly driven with a high load. For vehicles that are driven with varying loads, we recommend the Progressive additional spring kit. Delivery without expert opinion, registration by individual approval is possible.

This set conists of: 1x TREKFINDER Coil Spring Set 2x Upper Supports 2x Lower Supports

Air Suspension Defender 90/110/130/Discovery I/ Range Rover Classic These auxiliary air springs provide a more stable ride and noticeably improve the handling of the vehicle. Lateral roll of the vehicle is noticeably reduced. The air springs are inflated using the supplied hoses which are routed to an accessible location. A hand pump can be used for this purpose, as can a compressor, or they can simply be filled at the petrol station. They are available for Defender 90, Disovery U and Range Rover Classic or Defender 110 / 130.Supplied in pairs, the auxiliary air springs can be adjusted to suit all conceivable load and off-road conditions. Simply increase the air volume for increased load, or deflate for driving without additional load.The springs are made from durable and dimensionally stable polyurethane.Please select the vehicle.

Caster correction wedges If you raise your car’s suspension or exchange your original shocks, most of the time axle or wheel geometry, i.e. caster or camber angles, will get out of alignment. To correct aberrations on axles with leaf springs, especially our 3-leaf parabolic springs for the 88” rear axle Land Rover Series II, IIA und III, we are now carrying these caster correction wedges. The wedges provide 3° correction and have a 13 mm pin opening.

Comfort spring set TREKFINDER for LAND ROVER Defender 110 with VA +20 / HA +0 millimetres the lifting is +20 millimetres at the front axle, +0 millimetres at the rear axle matched to the TREKFINDER® shock absorbers Raid ( article no. 90-5470 + 905471 ) SCOPE OF DELIVERY: 4 pieces TREKFINDER® coil springs progressive 1 piece TÜV® parts certificate Suitable for Land Rover Defender 110 until BJ 2016  

Price per unit

Price per unit

Price per unit

Price per unit

Price per unit

Spring lift-kit for Land Rover Defender 110, manufactured by Trekfinder. The kit elevates the ride height by about 40 mm and optimizes the riding comfort. Renowend suspension manufacturers H&R and STOCK & STEIN joined forces to create a no-compromise solution and this is the result. The progesively wound springs allow for 80 kg of additional load on the front and 250 kg on the back wheels, while allowing you to still use the stock dampers. The package contains: * 4 x TREKFINDER progesive springs* 1 x TÜV Parts-Certificate Due to the increased articulation angle of the front cardan shaft, which is caused by the lift, we recommend installing a cardan shaft with a double joint.Cardan shaft for Defender Td4 from MY07 can be found here.Cardan shaft for Defender Tdi / Td5 to MY07 can be found here.

Spring lift-kit for Land Rover Defender 90, manufactured by Trekfinder. The kit elevates the ride height by about 40 mm and optimizes the riding comfort. Renowend suspension manufacturers H&R and STOCK & STEIN joined forces to create a no-compromise solution and this is the result. The progesively wound springs allow for 80 kg of additional load on the front and 250 kg  on the back wheels, while allowing you to still use the stock dampers. The package contains : * 4 x TREKFINDER progesive springs* 1 x TÜV Parts-Certificate Due to the increased articulation angle of the front cardan shaft, which is caused by the lift, we recommend installing a cardan shaft with a double joint.Cardan shaft for Defender Td4 from MY07 can be found here.Cardan shaft for Defender Tdi / Td5 to MY07 can be found here.

Lowering Kit for a Land Rover Defender 110 by TREKFINDER with progressively winded springs incl. TÜV parts-certificate. Made by H&R. The lowering kit reduces the ride height by about 45 mm in the front and 40 mm in the rear. The springs themself are maufactured from a special spring steel and polyurethane coated. The springs are designed to work with the stock dampers, but the load on the rear axel must be reduced to 1800 kg ! The springs guarantee  a comfortable ride, while reducing body roll dramaticly and improving the handling. The scope of delivery: 4x Lowering Springs1x TÜV Parts-certificate.

Parabolic springs for 88" and 109", Land Rover Series II, IIA and III, front (2-layer) and rear axle (3-layer); including Cellular Dynamic shock absorbers Basically, a parabolic spring is a spring that consists of two or more leaves. The leaves only touch in three places: In the centre, where they are attached to the axle, and at the outer ends, where they are attached to the vehicle. Between these points, the leaves do not touch, unlike conventional leaf springs.Since in the Parabolic spring a spring tapers from the wide centre to the outer ends, a single leaf acts like a complete spring - the thickness of the spring changes according to a parabola and provides a constant distribution of tension. Each leaf has more or less the shape of a complete multi-leaf spring and can therefore withstand a comparable force. The high quality OEM parabolic springs are paired with Cellular Dynamic shock absorbers. Also included in the kit are leaf spring correction wedges that can be used to correct caster or diff bolt angle by 3 degrees. The parabolic springs include u-bolts and nuts. Scope of supply: 2 x Parabolic Springs - 2 or 3 sheet 2 x Cellular Dynamic long travel shock absorbers 2 x Angle correction wedges

Inside spring set by TREKFINDER, optional for the rear axel with installed liftkit. Scope of Delivery: 2x Progressively wound spring coils

TREKFINDER suspension kit LAND ROVER Defender II 90/110 with steel suspension / coil springs +50 mm sporty tight tuning without being uncomfortable eliminates the standard spongy, indirect suspension and driving behaviour Height increase approx. 50 mm ( depending on type and version ) trailer operation is still permissible The length of the shock absorbers, brake lines and other lines is sufficient. Version: Defender 90: Suitable for the following models: Vehicle manufacturer: Jaguar Landrover (GB)Vehicle type / make: LE / Land RoverTrade name / Design: Defender 90 L663 ( M1G o. N1G ) WITHOUT air suspension!Perm. axle loads ( v / h ) in kg: 1400 / 1775EC-TG no.:e5*2007/46*0092..e5*2007/46*0152.. Version: Defender 110: Suitable for the following models: Vehicle manufacturer: Jaguar Landrover (GB)Vehicle type / make: LE / Land RoverTrade name / Model: Defender 110 L663 ( M1G o. N1G ) WITHOUT air suspension!Perm. axle loads ( v / h ) in kg: 1560 / 1800EC-TG no.:e5*2007/46*0092*..e5*2007/46*0125*.. Scope of delivery: 2 pieces TREKFINDER coil springs front axle / linear / black metallic 2 pieces TREKFINDER coil springs rear axle / progressive / black metallic 1 piece TÜV® parts certificate