HD suspension for Land Rover Defender 110 (for heavily loaded rear axles) Set consists of:  1x TREKFINDER coil springs  2x front axle shock absorbers 2x holder for additional spring, rear, bottom 2x bracket for additional spring, rear, top 1x lift spring set for Land Rover Defender 110 2x shock absorber Koni HeavyTrack RAID Defender  Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here.  Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.     

Inspection set for TREKFINDER steering damper - eye Delivery: 1 piece rubber bush1 piece of metal sleeve -------------------------------------------------- --------------------------------- Inspection set for TREKFINDER steering damper - pin Delivery: 1 piece hex nut1 piece metal plate outside2 pieces of metal plate inside2 pieces of rubber buffer

Lifting suspension TREKFINDER for SUZUKI Jimny I Type FJ|the lifting is approx. 55 millimetres SUPPLY: 1-SUJIF1.1 BILSTEIN - not hardness adjustable - very tight tuning 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, B6 not adjustable, Made by BILSTEIN 2 pieces TREKFINDER shock absorber rear axle, B6 not adjustable, Made by BILSTEIN 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate SUPPLY 1-SUJIF1.2: KONI - height adjustable - comfortable to very tight tuning possible 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, heavy track 5-way adjustable, Made by KONI 2 pieces TREKFINDER shock absorber rear axle, Heavy Track 5-way adjustable, Made by KONI 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate Info KONI: The suspension or dampers are delivered from the factory in the most comfortable damper setting ( open ). Ideal for vehicles that are driven daily on and off the road without additional weights. Fine damping of bumps, asphalt edges, holes, curbs etc. WITHOUT being spongy. WITHOUT being spongy! For applications and wishes that make a harder shock absorber sensible (e.g. roof rack, cable winch, camping equipment etc.), 5 hardness levels are available with the KONI shock absorber in order to be able to individually tighten the shock absorber! The levels are clearly noticeable when driving. In our opinion, there is a suitable set-up for every application. OPTIONAL additionally available:- for level compensation and can be mounted once per spring, the TREKFINDER spring spacer rings 10 mm with Art. No. 1-FDR10- the reinforced steering damper from TREKFINDER with the Art. No. 1-SUJILD.1  

Lifting suspension TREKFINDER for SUZUKI Jimny II type GJ from 10/2018 / HJ - the lifting is about 40-50 millimeters. Suitable for model / vehicles:Jimny type GJ from 2018 > / HJdepending on variant: with / without installed cable winch in front depending on variant: with / without steel braided brake line setwith or without LED light with manual transmissionwith automatic transmissionwith 1,5 L engine 75 Kwwith axle loads VA 680 Kg / HA 880 Kgwith ABE-EG number: e6*2007/46*0253*.. oder e6*2007/46*0515*.. SCOPE OF DELIVERY 1-SUJI2F1: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F2: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F3: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F4: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate Translated with www.DeepL.com/Translator (free version)

Spring Spacer Ring/ Trim Packer/ Lifting Ring TREKFINDER for SUZUKI Jimny I & II + 10 Millimeter in colour red - for levelling at the front or/and rear axle. Suitable for all Jimny models at the front and rear axle: Jimny II type GJ & HJ as of MY 2018 Jimny I type FJ until MY 2018 for the front axle spring for the rear axle spring 10 millimetre height adjustment SCOPE OF DELIVERY: 1 piece TREKFINDER polyurethane spring distance ring with marking TREKFINDER logo + FDR10 in colour red. NOTE: The spacer rings are listed in the TÜV® parts certificate for our TREKFINDER Jimny II complete suspension 40 mm and Jimny I suspension 55 mm and can therefore be optionally installed 1x per spring.A general TÜV® parts certificate is not available or is NOT included in the scope of delivery. MOUNTING INSTRUCTIONS: The installation is carried out between the upper end of the spring and the spring plate. Make sure that the brake line is long enough Make sure that the shock absorber is long enough. Check the headlight setting. The permissible height of the coupling ball must be observed. If there is a load-dependent headlight adjustment, e.g. for LED lights, this must be checked and, if necessary, adjusted or changed/extended. If a new measurement or calibration of the sensors of the driver assistance system is necessary due to the changed vehicle geometry of the vehicle, this must be carried out according to the specifications of the vehicle manufacturer. For vehicles with load-dependent brake pressure regulator, this must be readjusted to the empty level (according to the vehicle manufacturer's specifications). After retrofitting, the axle geometry of the vehicle must be measured and, if necessary, corrected according to the vehicle manufacturer's specifications.

Steering damper kit TREKFINDER for Suzuki Jimny I type FJ until 2018 the mounting of the steering damper is done on the frame and the tie rod, by means of special heavy duty mounting kits, with conceivably easy installation drilling, welding, deburring, painting etc. is NOT necessary for the installation of our steering damper optimal angle of attack to the steering rod by mounting with frame kit and at rotatable track rod angle, NO mounting at the thin gusset plate of the towing lug direct response due to the high stiffness of both mounting kits, no "bending" or "turning" as with other mounting points e.g. towing lug plate etc. very well suitable for Jimny`s WITH and WITHOUT height or lowering suitable for ALL Jimny I models (gasoline + diesel and 2/4WD) below in the text the models/the area of application are still separately specified (see KFZ certificate) the Foam Cell technology in the twin-tube damper with 35 mm piston rod and maximum volume, prevents the mixing of gas molecules in the oil, guarantees a long life and a perfect performance in ON- u. OFFROAD OPERATION track adjustment is NOT required after installation fits in combination with ALL engine and underride guards known to us SCOPE OF DELIVERY: 1 piece TREKFINDER steering damper/foam cell1 piece TREKFINDER mounting kit steering rod/galvanized1 piece TREKFINDER mounting kit frame/galvanized1 piece installation and assembly instructions1 piece TÜV® parts certificate The following area of application is listed in the parts certificate: Vehicle manufacturer: SUZUKI ( J ) Jimny / SANTANA ( E ) Jimny ConvertibleVehicle type: FJTrade name: Jimny / Jimny CabrioEC TG No.: e6*XXXX/XXX*0056*.. / e9*XXXX/XXX*0034*..

Steering damper reinforced TREKFINDER for SUZUKI Jimny II from 2018 type GJ & HJ reliably reduces, prevents and eliminates steering wheel vibrations in/on your Jimny if all attempts and efforts such as balancing the wheels, adjusting the toe, correcting the caster, replacing the wheel and steering knuckle bearings, etc. have not been successful........this steering damper will certainly help you :) the installation of the steering damper is very easy and plug and play, the standard damper is simply replaced, the new steering damper fits to the standard mounting points. drilling, welding, deburring, painting etc. is NOT necessary for the installation of our steering damper very suitable for Jimny's WITH and WITHOUT lowering or raising the vehicle the Foam Cell technology in the twin-tube damper with 35 mm piston rod and maximum volume prevents the mixing of gas molecules in the oil, guarantees a long service life and perfect performance in ON- and OFFROAD OPERATION track adjustment is NOT necessary after assembly SCOPE OF DELIVERY: 1 piece TREKFINDER steering damper/Foam Cell Technology

Trailing arm hanger kit TREKFINDER for SUZUKI Jimny I type FJ up to year of construction 2018 for the trailing arms at the attachment to the front axle for correction and optimisation of the caster angle recommended for suspensions from 3 cm of height increase 4 bushings with eccentric bore vulcanised in rubber

Trailing arm hanger kit TREKFINDER for SUZUKI Jimny II Type GJ & HJ from MY 2018 onwards for the trailing arms at the attachment to the front axle for correction/optimisation of the caster angle recommended for suspensions from 3 cm height adjustment onwards 4 bushings with eccentric bore vulcanised in rubber

Underride protection for SUZUKI Jimny type FJ MY 1998 to 2018 transferbox by TREKFINDER made of 8mm aluminium Underride protection TREKFINDER Heavy Duty for Suzuki Jimny transferbox (fits all Jimny models type FJ year of construction 1998 to 2018 (NOT from 2018 type GJ)) - incl. plug and switch protection made of 8 millimetre aluminium - super stable and flat design.ATTENTION: in Jimny models, transfer case mountings of different heights are installed ex works, it may be that you have to underlay the underride protection on both sides with washers - this individual adjustment allows minimum distance to the VTG - this in turn means optimum ground clearance off-road and is a technical advantage!The underride protection is mounted at the original points - no drilling is required.

Underride Protection for Suzuki Jimny II When you go Off-Road and you're pushing the limits of your vehicle, you should protect your cas as best you can. This Underride Protection, engineered to perfectly fit the second generation of Suzuki Jimny, now makes for a care free travel across all kinds of terrain. The 6 mm thick aluminium fits all engine sizes and all kinds of transmissions.  Additionally and for an even easier instalation, all the nuts and bolts are already included.

Underride protection kit TREKFINDER for SUZUKI Jimny 2 type GJ and HJ 5-piece suitable for all Jimny models of the type GJ built from the end of  2018, Typ HJ suitable for all engine and transmission types including all mounting parts attachment to original points of the vehicle super stable and flat heavy duty versions Delivery: underride protection linkage 5 mm anodised aluminum underrun protection axle tube / differential front axle 5 mm galvanized steel underride protection transfer case 8 mm aluminum underride protection exhaust gas control system 3 mm galvanized steel underrun protection axle tube / differential rear axle 5 mm galvanized steel

Underride protection TREKFINDER for SUZUKI Jimny II type GJ / HJ EXHAUST GAS CONTROL SYSTEM suitable for all Jimny models of the type GJ built from the end of  2018 and Type HJ suitable for all engine and transmission types from 3 millimeters of steel yellow galvanized including all mounting parts attachment to original points of the vehicle

TREKFINDER Wheel Spacer Mercedes G Wheel spacer for Mercedes G by TREKFINDER with conversion from screws to bolt system with 60 mm wheel spacer per axle made of high-strength, hard anodised aluminium.Scope of delivery for 2 axles. Details:    conversion from wheel bolt to wheel nut    60 mm per axle    made of high-strength aluminium alloy    DRM system + LK 130/5 + MZ84 + M14 x 1.5    price for two axles    the bolts for fixing the wheel to the axle are included in delivery    wheel nuts with ball collars are included    incl. parts certificate    easy plug&play mounting