TREKFINDER wheel spacer kit for INEOS Grenadier + 66 millimetres Track widening 66 mm by fitting spacer rings on the front and rear axle or only on the rear axle in conjunction with alloy wheels or standard INEOS Grenadier steel wheels. The following vehicles are approved according to the TÜV parts certificate: Vehicle manufacturer: Ineos Automotive (UK) / 2295Vehicle type: GN, GMCommercial designation/version: INEOS GRENADIER 6-cylinder diesel & petrol engine, 2+5 seaterEC - TG - No. : e9*2018/858*11384*... ; e9*2018/858*11385*... The following wheel/tyre combinations are approved according to the TÜV parts certificate: 265/70R17 with 7.5x17255/70R18 with 8.0x18 Scope of delivery: Selectable: 2 pieces (1 axle) or 4 pieces (2 axles) Aluminium wheel spacer plates, black anodised1 set of fixing nuts1 set of fitting and care instructions1 TÜV parts certificate Notes on installation:The screw-in length of all fastening elements must be at least 7.5 turns (M14x1.5).Ensure that the stud bolts are long enough.The bolted-on spacer rings are fastened to the vehicle using the fastening elements supplied by the spacer ring manufacturer (M14x1.5 tapered collar). The standard wheels are fastened with the standard fastening elements.The standard stud bolts may protrude slightly (up to 2 mm) beyond the wheel contact surface of the spacer rings. In conjunction with the standard Ineos steel wheels or LM wheels without "cast pockets", which can accommodate the standard stud bolts and nuts protruding beyond the wheel contact surface, the standard stud bolts must be shortened slightly. The minimum screw-in length of all fastening elements of 7.5 turns must be maintained. Wheel cover requirements:Adequate coverage of the wheel/tyre combination must be achieved by fitting 35 mm wide, permanently attached wheel cover extensions.The surface-mounted wheel cover extensions must be fitted at an angle of 30 degrees to the front and 50 degrees to the rear in relation to the vertical centre line of the wheel. Notes on the modification measure:There are no technical objections to the use of standard or other wheel/tyre combinations up to the above (limit) wheel/tyre combinations in conjunction with the described spacer rings if the following conditions are met: - Separate suitable expert reports are available for the wheel/tyre combinations and the conditions listed therein are complied with. In addition, the above-mentioned conditions must be observed and applied if necessary.- If other wheel/tyre combinations are used, their suitability (freedom of movement, driving behaviour, etc.) must be checked and verified separately.- There are no technical objections to the additional use of tested lowered or raised suspension (with parts certificate or ABE). In the case of suspension modifications with non-standard end stops, the suitability of the conversion must be checked or verified separately.  

Spring Distance Set ( FDS ) TREKFINDER for LAND ROVER Defender 90 Suitable for: Defender 90 Details: the lift is 30 millimetres made from aluminium black hard anodised the scope of delivery is for both axles, i.e. a complete car the discs are installed between the lower spring end and the spring plate the standard shock absorbers can still be used the discs may only be used with the standard springs SCOPE OF DELIVERY: 4 spacer discs 1 TÜV® parts certificate  

Spring spacer set ( FDS ) TREKFINDER for LAND ROVER Defender 110/130 Suitable for: Defender 110 Defender 130 Details: the lift is 30 millimetres made of aluminium black hard anodised the scope of delivery is for both axles, i.e. a complete car the discs are installed between the lower spring end and the spring plate the standard shock absorbers can still be used the discs may only be used with the standard springs please also note the optional mounting kit Art. No.: FDS-AN SCOPE OF DELIVERY: 4 spacer discs 1 TÜV® parts certificate  

Reinforced steering damper for the Land Rover Defender The reinforced steering damper is the ideal upgrade for the Land Rover Defender to significantly improve steering precision and driving stability, especially in off-road use. By reducing unwanted steering movements and vibrations caused by bumps in the road, this damper enables a safe and comfortable driving experience.Improved durability and performanceEquipped with advanced "Foam Cell" technology, which prevents oil and gas mixing, and a precision-machined 35 mm piston, the damper ensures optimum performance and durability both on and off-road. It is particularly effective against unstable handling caused by factors such as ruts, oversized tires or wheel spacers."Foam Cell" technologyFoam Cell technology prevents the oil from foaming, which ensures consistently high performance. This technology eliminates the risk of oil-air mixing and reduces the risk of overheating, making the damper particularly efficient.Increased ride comfortIn use, the damper effectively reduces unwanted movements and vibrations, which significantly increases ride comfort, especially at higher speeds and off-road. The stable steering control and improved directional stability in all conditions ensure a safe driving experience.When is a reinforced steering damper for the Defender useful?The reinforced steering damper for the Land Rover Defender is particularly useful if larger tires or a track widening are installed or the Defender is raised. This is because the conversion significantly increases the forces acting on the steering damper. In this case, the standard steering damper of the Defender quickly reaches its limits. The steering feels spongy and bumps in the road are very noticeable.Installation and registrationInstallation is straightforward and does not require TÜV registration, thanks to the adaptation to existing mounting points. Technical data: "Foam Cell" technology in twin-tube design 35 mm bore and sintered piston No TÜV registration required Simple installation on original mounting points  

Lowering spring kit TREKFINDER for INEOS Grenadier - approx. 30 millimetres the lowering is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines for vehicles WITHOUT winch the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Vehicle type / make: GN with EG-TG-No.: e9*2018/858*11385*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate

Lifting spring kit TREKFINDER for INEOS Grenadier + approx. 30 millimetres the lift is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines for vehicles WITHOUT cable winch the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Vehicle type / make: GN with EG-TG-No.: e9*2018/858*11385*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate <iframe width="1188" height="668" src="https://www.youtube.com/embed/Ex0-px1m0LE" title="INEOS GRENADIER Höherlegungsfedernsatz (+30mm) von TREKFINDER und H&amp;R" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen></iframe>

Lifting spring kit TREKFINDER for INEOS Grenadier + approx. 30 millimetres the lift is approx. 30 millimetres suitable for 6-cylinder diesel & petrol engines exclusively for vehicles type GM ( passenger car ) WITH additional weight ( approx. 80 kg ) due to a winch attachment at the front the standard shock absorbers can still be used Trailer operation is permitted Suitable for the following versions: Vehicle manufacturer: Ineos Automotive ( UK ) Commercial designation / version: INEOS GRENADIER Permissible axle loads ( v / h ) in kg: 1667 / 2150 Vehicle type / make: GM with EG-TG-No.: e9*2018/858*11384*... Scope of delivery: 4 pieces TREKFINDER coil springs ( HA progressive and VA linear ) 1 piece TÜV® parts certificate <iframe width="1188" height="668" src="https://www.youtube.com/embed/Ex0-px1m0LE" title="INEOS GRENADIER Höherlegungsfedernsatz (+30mm) von TREKFINDER und H&amp;R" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" allowfullscreen></iframe>

Lifting suspension TREKFINDER for SUZUKI Jimny I Type FJ|the lifting is approx. 55 millimetres SUPPLY: 1-SUJIF1.1 BILSTEIN - not hardness adjustable - very tight tuning 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, B6 not adjustable, Made by BILSTEIN 2 pieces TREKFINDER shock absorber rear axle, B6 not adjustable, Made by BILSTEIN 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate SUPPLY 1-SUJIF1.2: KONI - height adjustable - comfortable to very tight tuning possible 2 pieces TREKFINDER coil spring front axle, progressively wound, Made by H&R 2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R 2 pieces TREKFINDER shock absorber front axle, heavy track 5-way adjustable, Made by KONI 2 pieces TREKFINDER shock absorber rear axle, Heavy Track 5-way adjustable, Made by KONI 4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by ZF/LUCAS GIRLING 1 piece TREKFINDER TÜV® parts certificate Info KONI: The suspension or dampers are delivered from the factory in the most comfortable damper setting ( open ). Ideal for vehicles that are driven daily on and off the road without additional weights. Fine damping of bumps, asphalt edges, holes, curbs etc. WITHOUT being spongy. WITHOUT being spongy! For applications and wishes that make a harder shock absorber sensible (e.g. roof rack, cable winch, camping equipment etc.), 5 hardness levels are available with the KONI shock absorber in order to be able to individually tighten the shock absorber! The levels are clearly noticeable when driving. In our opinion, there is a suitable set-up for every application. OPTIONAL additionally available:- for level compensation and can be mounted once per spring, the TREKFINDER spring spacer rings 10 mm with Art. No. 1-FDR10- the reinforced steering damper from TREKFINDER with the Art. No. 1-SUJILD.1  

Lifting suspension TREKFINDER for SUZUKI Jimny II type GJ from 10/2018 / HJ - the lifting is about 40-50 millimeters. Suitable for model / vehicles:Jimny type GJ from 2018 > / HJdepending on variant: with / without installed cable winch in front depending on variant: with / without steel braided brake line setwith or without LED light with manual transmissionwith automatic transmissionwith 1,5 L engine 75 Kwwith axle loads VA 680 Kg / HA 880 Kgwith ABE-EG number: e6*2007/46*0253*.. oder e6*2007/46*0515*.. SCOPE OF DELIVERY 1-SUJI2F1: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F2: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®4 pieces TREKFINDER steel braided brake line, stainless steel & protective jacket, Made by LUCAS GIRLING®1 piece TREKFINDER mounting kit for models with LED headlight1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F3: 2 pieces TREKFINDER coil spring front axle, progressive wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate SCOPE OF DELIVERY 1-SUJI2F4: 2 pieces TREKFINDER coil spring front axle, linear wound, Made by H&R®.2 pieces TREKFINDER coil spring rear axle, progressively wound, Made by H&R®.2 pieces TREKFINDER shock absorber front axle, monotube gas pressure B6, Made by BILSTEIN®2 pieces TREKFINDER shock absorber rear axle, monotube gas pressure B6, Made by BILSTEIN®1 piece TREKFINDER mounting kit for models with LED headlights1 piece TREKFINDER TÜV® parts certificate Translated with www.DeepL.com/Translator (free version)

Wheel Spacers TREKFINDER for LAND ROVER Range Rover Type LG, Range Rover Sport Type LW    -  Widening per axle +44 mm / 40 mm millimetres  -  made of high-strength and black hard anodised aluminium alloy  -  incl. fixing material  -  incl. parts certificate  - Scope of delivery for 1 axle

TREKFINDER suspension kit LAND ROVER Defender II 90/110 with steel suspension / coil springs +50 mm sporty tight tuning without being uncomfortable eliminates the standard spongy, indirect suspension and driving behaviour Height increase approx. 50 mm ( depending on type and version ) trailer operation is still permissible The length of the shock absorbers, brake lines and other lines is sufficient. Version: Defender 90: Suitable for the following models: Vehicle manufacturer: Jaguar Landrover (GB)Vehicle type / make: LE / Land RoverTrade name / Design: Defender 90 L663 ( M1G o. N1G ) WITHOUT air suspension!Perm. axle loads ( v / h ) in kg: 1400 / 1775EC-TG no.:e5*2007/46*0092..e5*2007/46*0152.. Version: Defender 110: Suitable for the following models: Vehicle manufacturer: Jaguar Landrover (GB)Vehicle type / make: LE / Land RoverTrade name / Model: Defender 110 L663 ( M1G o. N1G ) WITHOUT air suspension!Perm. axle loads ( v / h ) in kg: 1560 / 1800EC-TG no.:e5*2007/46*0092*..e5*2007/46*0125*.. Scope of delivery: 2 pieces TREKFINDER coil springs front axle / linear / black metallic 2 pieces TREKFINDER coil springs rear axle / progressive / black metallic 1 piece TÜV® parts certificate

Inspection set for TREKFINDER steering damper - eye Delivery: 1 piece rubber bush1 piece of metal sleeve -------------------------------------------------- --------------------------------- Inspection set for TREKFINDER steering damper - pin Delivery: 1 piece hex nut1 piece metal plate outside2 pieces of metal plate inside2 pieces of rubber buffer

Underride Protection for Suzuki Jimny II When you go Off-Road and you're pushing the limits of your vehicle, you should protect your cas as best you can. This Underride Protection, engineered to perfectly fit the second generation of Suzuki Jimny, now makes for a care free travel across all kinds of terrain. The 6 mm thick aluminium fits all engine sizes and all kinds of transmissions.  Additionally and for an even easier instalation, all the nuts and bolts are already included.

Steering damper reinforced TREKFINDER for SUZUKI Jimny II from 2018 type GJ & HJ reliably reduces, prevents and eliminates steering wheel vibrations in/on your Jimny if all attempts and efforts such as balancing the wheels, adjusting the toe, correcting the caster, replacing the wheel and steering knuckle bearings, etc. have not been successful........this steering damper will certainly help you :) the installation of the steering damper is very easy and plug and play, the standard damper is simply replaced, the new steering damper fits to the standard mounting points. drilling, welding, deburring, painting etc. is NOT necessary for the installation of our steering damper very suitable for Jimny's WITH and WITHOUT lowering or raising the vehicle the Foam Cell technology in the twin-tube damper with 35 mm piston rod and maximum volume prevents the mixing of gas molecules in the oil, guarantees a long service life and perfect performance in ON- and OFFROAD OPERATION track adjustment is NOT necessary after assembly SCOPE OF DELIVERY: 1 piece TREKFINDER steering damper/Foam Cell Technology

Trailing arm hanger kit TREKFINDER for SUZUKI Jimny II Type GJ & HJ from MY 2018 onwards for the trailing arms at the attachment to the front axle for correction/optimisation of the caster angle recommended for suspensions from 3 cm height adjustment onwards 4 bushings with eccentric bore vulcanised in rubber

Spring Spacer Ring/ Trim Packer/ Lifting Ring TREKFINDER for SUZUKI Jimny I & II + 10 Millimeter in colour red - for levelling at the front or/and rear axle. Suitable for all Jimny models at the front and rear axle: Jimny II type GJ & HJ as of MY 2018 Jimny I type FJ until MY 2018 for the front axle spring for the rear axle spring 10 millimetre height adjustment SCOPE OF DELIVERY: 1 piece TREKFINDER polyurethane spring distance ring with marking TREKFINDER logo + FDR10 in colour red. NOTE: The spacer rings are listed in the TÜV® parts certificate for our TREKFINDER Jimny II complete suspension 40 mm and Jimny I suspension 55 mm and can therefore be optionally installed 1x per spring.A general TÜV® parts certificate is not available or is NOT included in the scope of delivery. MOUNTING INSTRUCTIONS: The installation is carried out between the upper end of the spring and the spring plate. Make sure that the brake line is long enough Make sure that the shock absorber is long enough. Check the headlight setting. The permissible height of the coupling ball must be observed. If there is a load-dependent headlight adjustment, e.g. for LED lights, this must be checked and, if necessary, adjusted or changed/extended. If a new measurement or calibration of the sensors of the driver assistance system is necessary due to the changed vehicle geometry of the vehicle, this must be carried out according to the specifications of the vehicle manufacturer. For vehicles with load-dependent brake pressure regulator, this must be readjusted to the empty level (according to the vehicle manufacturer's specifications). After retrofitting, the axle geometry of the vehicle must be measured and, if necessary, corrected according to the vehicle manufacturer's specifications.

Trailing arm hanger kit TREKFINDER for SUZUKI Jimny I type FJ up to year of construction 2018 for the trailing arms at the attachment to the front axle for correction and optimisation of the caster angle recommended for suspensions from 3 cm of height increase 4 bushings with eccentric bore vulcanised in rubber

Comfort spring set TREKFINDER for LAND ROVER Defender 110 with VA +20 / HA +0 millimetres the lifting is +20 millimetres at the front axle, +0 millimetres at the rear axle matched to the TREKFINDER® shock absorbers Raid ( article no. 90-5470 + 905471 ) SCOPE OF DELIVERY: 4 pieces TREKFINDER® coil springs progressive 1 piece TÜV® parts certificate Suitable for Land Rover Defender 110 until BJ 2016  

Mounting material for 1 piece KONI/ TREKFINDER Heavy Track RAID damper 90-5374SP1 + 90-5470, top and bottom Mounting material for the pin mounting of the shock absorber on both sides Suitable for all LAND ROVER Defender models Scope of delivery: 8 pieces metal washer + 4 pieces rubber + 2 pieces nut self-locking

Metal sleeve rubber mount for Koni Heavy Track RAID shock absorber 90-5375SP1 + 90-5471, top suitable for all years of construction! Scope of delivery: 1 piece

Mounting material for 2 pieces KONI/ TREKFINDER Heavy Track RAID  shock absorber 90-5375SP1 + 90-5471 below Mounting material for the pin fastening of the shock absorber - suitable for LAND ROVER Defender models up to approx. 2001 ( no pot mounting ) Scope of delivery: 8 pieces metal washer + 4 pieces rubber + 2 pieces self-locking nut

Wheel spacer TREKFINDER for JEEP® Wrangler JK +60 millimetres per axle ( 30 mm per disc/ side ) black anodised Suitable for the following models/ Wrangler models: Model Jeep Wrangler/ Jeep Wrangler Unlimited Type JK EG-TG-No. e4*2001/116*0116* Details: Made of high-strength aluminium alloy Black hard anodised with 60 mm wheel spacer per axle (30 mm per side) DRM system (washers with pressed-in bolts are slid over the existing vehicle studs and screwed tight) Use with steel rims is prohibited incl. fastening material (10 cone collar nuts) incl. TÜV® parts certificate Price and scope of delivery is for one axle The spacer rings may only be fitted in conjunction with standard LM wheels and in combination with the cone collar nuts supplied. The spacer rings are not permitted in conjunction with steel wheels. The screw-in length of all fastening elements must be at least 6.5 turns. Ensure that the stud bolts are of sufficient length. The notes in the assembly instructions for the spacer rings must be observed. The installation of spacer rings is not permitted if the diameter of the spacer rings is smaller than the diameter of the wheel contact surface. A modification approval by TÜV, DEKRA etc. is required. However, the entry in the vehicle documents can also only be made at the next appointment with the responsible registration authority. In the meantime, it is sufficient to carry the parts certificate and the confirmation of the modification approval. All fastening elements must be checked with a suitable torque spanner after approx. 100 km of driving. Compatibility or usability of specific snow chains cannot be guaranteed. PLEASE NOTE: Only in conjunction with LM wheels with corresponding GIESSTASCHEN = standard stud bolts or nut heads protruding beyond the wheel surface may sink.The standard stud bolts may have to be shortened.The minimum screw-in length of all fastening elements of 6.5 turns must be maintained.

Steering damper kit TREKFINDER for Suzuki Jimny I type FJ until 2018 the mounting of the steering damper is done on the frame and the tie rod, by means of special heavy duty mounting kits, with conceivably easy installation drilling, welding, deburring, painting etc. is NOT necessary for the installation of our steering damper optimal angle of attack to the steering rod by mounting with frame kit and at rotatable track rod angle, NO mounting at the thin gusset plate of the towing lug direct response due to the high stiffness of both mounting kits, no "bending" or "turning" as with other mounting points e.g. towing lug plate etc. very well suitable for Jimny`s WITH and WITHOUT height or lowering suitable for ALL Jimny I models (gasoline + diesel and 2/4WD) below in the text the models/the area of application are still separately specified (see KFZ certificate) the Foam Cell technology in the twin-tube damper with 35 mm piston rod and maximum volume, prevents the mixing of gas molecules in the oil, guarantees a long life and a perfect performance in ON- u. OFFROAD OPERATION track adjustment is NOT required after installation fits in combination with ALL engine and underride guards known to us SCOPE OF DELIVERY: 1 piece TREKFINDER steering damper/foam cell1 piece TREKFINDER mounting kit steering rod/galvanized1 piece TREKFINDER mounting kit frame/galvanized1 piece installation and assembly instructions1 piece TÜV® parts certificate The following area of application is listed in the parts certificate: Vehicle manufacturer: SUZUKI ( J ) Jimny / SANTANA ( E ) Jimny ConvertibleVehicle type: FJTrade name: Jimny / Jimny CabrioEC TG No.: e6*XXXX/XXX*0056*.. / e9*XXXX/XXX*0034*..

Silencer / Spacer f. height compensation (P38 or Salisbury axle)  Description:  the item can be used on the rear axle on 110s and 130s.  optimal possibility for level compensation/ the height adjustment is 10 millimetres the ring consists of a zinc, phosphated metal ring with coil spring centring and vulcanised NR/ SBR rubber the rubberised surface of the ring reduces the transmission of vibration noise the washer is placed between the spring end and the spring plate, max. one washer per spring end is possible, i.e. max. two washers per spring, i.e. max. 20 mm height increase per spring is possible price per unit

Suspension for Land Rover Defender 130 Lightweight Set consists of:  1x TREKFINDER lift spring set for Land Rover Defender 1102x shock absorber for Land Rover Defender 90 / 110 / 130 front axle2x shock absorber Koni Heavy Track RAID Defender Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here.  Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.     

HD suspension for Land Rover Defender 110 (for heavily loaded rear axles) Set consists of:  1x TREKFINDER coil springs  2x front axle shock absorbers 2x holder for additional spring, rear, bottom 2x bracket for additional spring, rear, top 1x lift spring set for Land Rover Defender 110 2x shock absorber Koni HeavyTrack RAID Defender  Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here.  Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.     

Suspension for Land Rover Defender 130 Set consists of:  1x TREKFINDER coil springs 1x lift spring set 2x shock absorbers for Land Rover Defender 90 / 110 / 130 2x shock absorbers Koni Heavy Track RAID Defender Due to the increased articulation angle of the front cardan shaft caused by the lift, we recommend the installation of a cardan shaft with double joint.  Cardan shaft for Defender Td4 from MY07 can be found here.  Cardan shaft for Defender Tdi/Td5 up to MY07 can be found here.     

Inside spring set by TREKFINDER, optional for the rear axel with installed liftkit. Scope of Delivery: 2x Progressively wound spring coils

Underride protection TREKFINDER for SUZUKI Jimny II type GJ / HJ EXHAUST GAS CONTROL SYSTEM suitable for all Jimny models of the type GJ built from the end of  2018 and Type HJ suitable for all engine and transmission types from 3 millimeters of steel yellow galvanized including all mounting parts attachment to original points of the vehicle

Underride protection kit TREKFINDER for SUZUKI Jimny 2 type GJ and HJ 5-piece suitable for all Jimny models of the type GJ built from the end of  2018, Typ HJ suitable for all engine and transmission types including all mounting parts attachment to original points of the vehicle super stable and flat heavy duty versions Delivery: underride protection linkage 5 mm anodised aluminum underrun protection axle tube / differential front axle 5 mm galvanized steel underride protection transfer case 8 mm aluminum underride protection exhaust gas control system 3 mm galvanized steel underrun protection axle tube / differential rear axle 5 mm galvanized steel

Lifting spring set TREKFINDER for Land Rover Discovery Sport Type LC approx. +30 millimetres the ride height is approx. +30 millimetres suitable for Land Rover Discovery Sport Type LC the standard shock absorbers can still be used Scope of delivery: 4x piece TREKFINDER coil spring 1x piece TREKFINDER sticker 1x piece parts certificate

Suspension lift kit TREKFINDER for JEEP® Renegade +30 millimetres the lift is approx. +30 millimetressuitable for the Renegade 4WD type BU model ‘TRAILHAWK’.A suitable version for the standard model of the Renegade 4WD Type BU can be purchased here.The standard shock absorbers can still be usedScope of delivery:  4x TREKFINDER coil spring 1x TREKFINDER sticker 1x piece parts certificate